Duct Leakage Test in Glenside, PA

Improve HVAC performance and ensure energy code compliance with dependable duct leakage test in Glenside, PA. Our certified technicians trace and measure duct leaks, supporting homeowners and builders in enhancing comfort, lowering energy waste, and staying compliant with state codes.

Why Duct Leakage Test is Important In Glenside, PA

States and municipalities now follow the 2015 IECC, International Energy Conservation Code for single-family residences, as well as the 2018 International Energy Conservation Code for multi-family structures. The change will carry significant implications for home builders and HVAC contractors serving communities in the state. A Duct Leakage Test as well as a Blower Door Test in newly constructed or remodeled homes is now required in accordance with the 2015 regulations. Did you know that duct systems can be major sources of air leakage in homes across Pennsylvania, New Jersey, and Delaware? Leaked air can cause higher energy expenses, burden your HVAC system, and push dust and insulation into different areas of your home. This makes duct leakage test essential for both new and older homes. Continue reading to understand why duct leakage test matters and how it can benefit you.

888 213-3975

What Our Clients Say

How a Duct Leakage Test Is Conducted

To initiate testing, your technician will seal all supply and return registers except for the main return or air handler during a duct leakage test in Glenside, PA. A duct blaster — a specially calibrated fan — is then connected to the opening. It depressurizes the duct system to expose areas where air is leaking.

The duct blaster, working hand in hand with a precision pressure sensor, measures airflow and identifies leaks in the ductwork without impacting your home. A duct leakage test — often known as a duct blaster test — exposes duct air loss, allowing you to apply the most effective sealing techniques.

duct leakage test is easy, clean, and unobtrusive for residents in the home. Most tests in Glenside, PA are completed in roughly 30 to 60 minutes, and the resulting enhancements can support your home’s comfort and efficiency long-term.

How to Measure Duct Leakage

Duct leakage is measured using cubic feet per minute (CFM) per 100 square feet of conditioned floor area. Your technician uses a nanometer to pick up minor pressure shifts that indicate the level of air leakage within the ducts. Understanding this number helps you pinpoint leakage points, think through potential improvements, and verify your home’s adherence to local energy code requirements in Glenside, PA.

Cost of Excessive Duct Leakage

If you’re struggling with expensive utility bills, inconsistent indoor temperatures, or continual HVAC problems, duct leakage might be the culprit. According to ENERGY STAR, the typical home loses between 20% and 30% of its conditioned air due to duct leaks. When outdoor temperatures enter your system, the HVAC must work harder to compensate, resulting in higher energy costs and reduced comfort.

Overworked equipment also puts extra stress on the system, resulting in breakdowns and increased repair costs. Proper duct sealing helps protect and extend the long-term lifespan of your HVAC system, minimizing the need for repeated maintenance.

Duct leaks can also allow the entry of dust, mold spores, moisture, and a range of contaminants into the duct system. This can negatively influence allergies, weaken indoor air quality, and lead to expensive long-term damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC requires new homes to have fully sealed duct systems using modern, energy-efficient materials such as mastic, foil tape, and insulation. But what happens when leaks are trapped deep inside wall or ceiling cavities?

Aerosol sealing technology (AeroSeal) offers a method to access hidden leaks deep within ductwork. To execute this method, all vents are sealed shut except a single access point. The HVAC system is isolated, and a machine is attached to the duct network. It pressurizes the ducts and applies a fine aerosol sealant that fills tiny openings where standard sealing cannot reach.

This method is effective at treating small to medium leaks. However, big openings may still need to be addressed with manual mastic-and-tape sealing. Technicians use a duct leakage test before and after aerosol sealing to evaluate how much leakage has been lowered and verify the results.

Common Areas of Duct Leakage

The most typical place where ducts leak air is at their joints. Ductwork is built from multiple metal sections pressed tightly with fittings and metal bands, yet these joints are rarely airtight.

As your HVAC system moves through annual heating and cooling cycles, the ductwork expands and then contracts. Over time, this movement leads to joint loosening, generating gaps and leaks — a clear reason duct leakage test is recommended for new and older homes in Glenside, PA.

Many energy auditors detect duct leakage by physically checking the ducts and using a small tool to assess the width of joint gaps. If your duct system has not been properly sealed with mastic and approved tape, it’s very likely that leakage exists.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system needs to be under 4 CFM per 100 square feet when the air handler is installed, or 3 CFM per 100 square feet when it isn’t. For new construction, the home must pass a duct leakage test before qualifying for an occupancy certificate.

If your home in Glenside, PA doesn’t receive a passing duct leakage result, you are likely overpaying for heating and cooling — and putting significant long-term strain on your HVAC setup. Meeting the 3–4 CFM requirement is required not only for code approval but for keeping your home efficient and comfortable.

Your technician will also offer specialized recommendations to repair leakage issues so you can meet passing requirements, reduce utility bills, and improve your home’s performance.

Local Energy Audits — affordable duct leakage test in Glenside, PA

Local Energy Audits proudly provides service to homeowners and builders throughout Glenside, PA and the surrounding region. We specialize in identifying duct leakage and energy inefficiencies using blower door tests and duct leakage tests. Whether you’re building a new home or improving an existing one, we’re here to help.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.

The Duct Leakage Test Steps Explained

A duct leakage test begins by taping off all ducts and registers with duct mask tape on the supply and return sides.

After the registers are sealed, we attach the duct tester to either the unit itself or a main return.

The ducts are then placed under 25 Pascals of negative pressure. With the ducts depressurized, we obtain the leakage reading using the nanometer.

Schedule Your Duct Leakage Test in Glenside, PA

Ensure your HVAC system is efficient, compliant, and performing at its best with professional duct leakage test in Glenside, PA. Whether you’re a homeowner working to improve comfort or a contractor closing out a project with a final inspection, our certified team provides fast, accurate, and affordable testing.

We use industry-standard duct blaster equipment and give on-site support to help you pass your test, limit wasted energy, and strengthen the long-term health of your HVAC system.

📞 Call 888-213-3975 ✉️ Request a Quote

Serving homeowners, builders, and contractors across Glenside, PA with dependable and energy-efficient testing solutions.