Duct Leakage Test in Hoboken, NJ

How a Duct Leakage Test Is Conducted

To begin performing a duct leakage test in Hoboken, NJ, your technician closes off all supply and return registers except the main return or air handler system. A duct blaster, which is a specially calibrated fan, is then installed at the opening. The fan depressurizes the ducts, helping identify all points where air may be escaping.

The duct blaster collaborates with a precision pressure sensor to evaluate airflow and locate leaks throughout the ductwork without disturbing your household. A duct leakage test — sometimes referred to as a duct blaster test — uncovers air leaks in your ductwork so you can determine the ideal sealing approach.

duct leakage test is fast, tidy, and causes no disruption for residents. Most tests in Hoboken, NJ are completed within 30 to 60 minutes, and the improvements can benefit your home’s comfort and efficiency for years.

How to Measure Duct Leakage

Duct leakage is measured in cubic feet per minute (CFM) per 100 square feet of conditioned space. Your technician uses a nanometer to register small pressure differences, which help calculate how much air is leaking from the ducts. Understanding this number allows you to identify concerns, evaluate upgrade opportunities, and determine whether your home fulfills local energy code requirements in Hoboken, NJ.

Cost of Excessive Duct Leakage

If you’re dealing with rising utility bills, inconsistent room temperatures, or repeated HVAC issues, duct leakage could be the reason. According to ENERGY STAR, most homes lose 20% to 30% of their conditioned air through leaking ductwork. When outside hot or cold air seeps into your system, your HVAC must compensate, leading to higher energy costs and diminished comfort.

Overworked equipment also leads to more breakdowns and costly repairs. Proper duct sealing helps preserve the long-term efficiency of your HVAC system, boosting its lifespan and cutting down on regular maintenance needs.

Duct leaks can also allow dust, mold spores, excess moisture, and other contaminants into the duct system. This can intensify allergy symptoms, harm indoor air quality, and cause long-term structural damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC states that new homes must have duct systems sealed completely with energy-efficient products such as mastic, foil tape, and insulation. But what happens when air leaks are concealed deep in the walls or ceilings?

Aerosol sealing technology (AeroSeal) can identify and seal leaks that lie deep inside ductwork. To use this method, technicians seal all vents except one access point. The HVAC system is isolated, and a machine is hooked up to the duct system. It pressurizes the ducts and circulates a fine aerosolized sealant that locates and fills tiny leaks beyond the reach of typical sealing.

This method works best for small to medium leaks. However, large openings usually require traditional manual sealing using mastic and tape. Technicians run leakage tests both before and after aerosol sealing to gauge how much air loss decreased and confirm proper results.

Common Areas of Duct Leakage

The most common spot where air escapes in duct systems is the joints. Ductwork features several metal pieces pressed together using tight fittings and metal bands, though these areas are seldom airtight.

As your HVAC system moves through annual heating and cooling cycles, the ductwork expands and then contracts. Over time, this movement gradually loosens the joints, creating leaks and gaps — highlighting the importance of duct leakage test in both new and older homes in Hoboken, NJ.

Many energy auditors assess duct leakage by touching the ductwork and using a small tool to check the width of gaps where joints connect. If your duct system isn’t sealed with mastic and approved tape, there’s a good chance that leaks are occurring.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must remain below 4 CFM per 100 square feet with the air handler installed, or 3 CFM per 100 square feet if the air handler is missing. For new construction, a passing duct leakage test is a required step before final occupancy certification can be awarded.

If your home in Hoboken, NJ cannot achieve a passing duct leakage score, you are likely wasting money on heating and cooling — and increasing wear on your HVAC system over time. Meeting the 3–4 CFM requirement is fundamental not only for code adherence but for boosting your home’s long-term efficiency and comfort.

Your technician will also give expert suggestions on correcting leakage issues, allowing you to pass the test, lower utility expenses, and improve your home’s overall efficiency.

Local Energy Audits — affordable duct leakage test in Hoboken, NJ

Local Energy Audits is proud to work with customers in Hoboken, NJ and all nearby areas. We specialize in identifying duct leakage and energy inefficiencies using blower door tests and duct leakage tests. Whether you’re building a new home or improving an existing one, we’re here to help.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.