Duct Leakage Test in Roxbury, NJ

How a Duct Leakage Test Is Conducted

To kick off a duct leakage test in Roxbury, NJ, your technician will block all supply and return registers while keeping the main return or air handler accessible. A duct blaster, which is a specially calibrated fan, is then installed at the opening. The fan depressurizes the ducts, helping identify all points where air may be escaping.

The duct blaster uses its precision pressure sensor partner to measure airflow and uncover duct leaks without causing any home disruption. A duct leakage test — often known as a duct blaster test — exposes duct air loss, allowing you to apply the most effective sealing techniques.

duct leakage test is quick, neat, and intentionally non-intrusive for anyone living in the home. Most tests in Roxbury, NJ are wrapped up in 30 to 60 minutes, with improvements that continue to boost comfort and efficiency for years.

How to Measure Duct Leakage

Duct leakage is determined in cubic feet per minute (CFM) for every 100 square feet of conditioned interior space. Your technician uses a nanometer to measure tiny pressure changes, revealing how much air is escaping through the ducts. Understanding this number helps you pinpoint leakage points, think through potential improvements, and verify your home’s adherence to local energy code requirements in Roxbury, NJ.

Cost of Excessive Duct Leakage

If elevated utility bills, shifting temperatures, or repeated HVAC issues occur in your home, duct leakage may be the factor behind them. According to ENERGY STAR, typical duct systems lose 20% to 30% of conditioned air through leaks. Hot or cold outside air creeping into your system forces the HVAC to work inefficiently, increasing energy spending and reducing comfort.

Overworked equipment also increases the likelihood of breakdowns and drives up repair costs. Proper duct sealing helps preserve the long-term efficiency of your HVAC system, boosting its lifespan and cutting down on regular maintenance needs.

Duct leaks can also allow dust, mold spores, excess moisture, and other contaminants into the duct system. This can intensify allergy symptoms, harm indoor air quality, and cause long-term structural damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC sets a requirement that all new homes feature ducts sealed completely with modern materials like mastic, foil tape, and insulation. But what if the leaks are buried far inside your walls or ceilings?

Aerosol sealing technology (AeroSeal) is an effective solution for reaching hidden ductwork leaks. To conduct this method, all vents are blocked except for one access point. The HVAC system is isolated, and a machine is connected to the duct system. It pressurizes the ducts and releases a fine sealant mist that finds and fills small holes that traditional sealing methods cannot access.

This method is very effective for minor to moderate leaks. However, substantial openings may still need traditional sealing with mastic and tape. Technicians use a duct leakage test before and after aerosol sealing to evaluate how much leakage has been lowered and verify the results.

Common Areas of Duct Leakage

The most usual spot for duct air leakage is the joints. Ductwork is composed of various metal pieces pressed together using tight fittings and metal bands, but these seals are hardly ever fully airtight.

As your HVAC system warms and cools over the seasons, the ductwork expands and then contracts. Over time, this movement leads to joint loosening, generating gaps and leaks — a clear reason duct leakage test is recommended for new and older homes in Roxbury, NJ.

Many energy auditors detect leaks by checking the duct surfaces by hand and using a small tool to measure joint gap width. If your duct system does not include sealing with mastic and approved tape, leakage is highly likely.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system needs to register under 4 CFM per 100 square feet with the air handler attached, or 3 CFM per 100 square feet without it attached. For new construction, no home can receive an occupancy certificate without first passing a duct leakage test.

If your home in Roxbury, NJ doesn’t pass a duct leakage test, chances are you’re paying more for heating and cooling — and adding long-term stress to your HVAC equipment. Meeting the 3–4 CFM requirement is key not only for staying code-compliant but for maintaining energy efficiency and consistent comfort in your home.

Your technician will also provide expert insights into correcting leakage issues so you can meet passing standards, lower your utility expenses, and improve overall home performance.

Local Energy Audits — affordable duct leakage test in Roxbury, NJ

Local Energy Audits proudly provides solutions to customers throughout Roxbury, NJ and surrounding regions. We specialize in uncovering duct leakage and energy inefficiencies using both blower door tests and duct leakage tests. Whether you’re starting a new build or improving a current home, we’re here to assist.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.