Duct Leakage Test in Hazlet, NJ

Ensure your HVAC system is sealed, efficient, and fully compliant with local regulations through duct leakage test in Hazlet, NJ. Our certified technicians trace and measure duct leaks, supporting homeowners and builders in enhancing comfort, lowering energy waste, and staying compliant with state codes.

Why Duct Leakage Test is Important In Hazlet, NJ

Numerous states and municipalities rely on the 2015 IECC, International Energy Conservation Code for single-family properties and apply the 2018 International Energy Conservation Code to multi-family properties. The change will lead to several key implications for home builders and HVAC contractors working across the state. A Duct Leakage Test along with the required Blower Door Test must now be conducted on any newly built or remodeled home as per the 2015 regulations. Did you know that duct leakage is one of the most common issues affecting homes in Pennsylvania, New Jersey, and Delaware? Leaked air can increase your energy costs, overwork your HVAC system, and distribute insulation particles and dust around your home. This makes duct leakage test critical for both modern and older homes. Continue reading to explore why duct leakage test is important and how you benefit from it.

888 213-3975

What Our Clients Say

How a Duct Leakage Test Is Conducted

To begin a duct leakage test in Hazlet, NJ, your technician will seal off all supply and return registers except for the main return or the air handler. A duct blaster, which is a specially calibrated fan, is then installed at the opening. The fan depressurizes the ducts, helping identify all points where air may be escaping.

The duct blaster, combined with a precision pressure sensor, measures airflow and detects leaks in the duct system without causing any disturbance in your home. A duct leakage test — often referred to as a duct blaster test — identifies air loss in your ducts, allowing you to find the most effective ways to seal them.

duct leakage test is quick, low-impact, and does not disturb residents. Most tests in Hazlet, NJ take only 30 to 60 minutes, yet the comfort and efficiency gains can last for years.

How to Measure Duct Leakage

Duct leakage is measured using cubic feet per minute (CFM) per 100 square feet of conditioned floor area. Your technician uses a nanometer to pick up minor pressure shifts that indicate the level of air leakage within the ducts. Understanding this number helps you recognize where issues exist, plan meaningful improvements, and check your home against local energy code requirements in Hazlet, NJ.

Cost of Excessive Duct Leakage

If you’re experiencing spikes in utility bills, uncomfortable temperature variations, or ongoing HVAC repair needs, duct leakage may be to blame. According to ENERGY STAR, typical duct systems lose 20% to 30% of conditioned air through leaks. When your system pulls in hot or cold outdoor air, the HVAC unit has to work harder, driving up energy usage and reducing comfort indoors.

Overworked equipment also makes breakdowns more common and repairs more expensive. Proper duct sealing helps support the long-term durability of your HVAC system, lengthening its lifespan and minimizing ongoing maintenance demands.

Duct leaks can also allow dust, mold spores, excess moisture, and other contaminants into the duct system. This can negatively influence allergies, weaken indoor air quality, and lead to expensive long-term damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC requires that all new homes feature fully sealed duct systems utilizing updated, energy-efficient materials like mastic, foil tape, and insulation. But what happens when air leaks are concealed deep in the walls or ceilings?

Aerosol sealing technology (AeroSeal) is used to address openings concealed inside duct systems. To start this method, all vents are blocked except for one access location. The HVAC system is isolated, and a machine is attached to the ducts. It pressurizes the ducts and emits a fine aerosol sealant that fills tiny gaps and holes that standard sealing methods can’t access.

This method works efficiently for small to medium leaks. However, larger gaps usually require manual sealing using mastic and tape. Technicians carry out a duct leakage test before and after aerosol sealing to assess how much leakage has improved and ensure the treatment was effective.

Common Areas of Duct Leakage

The most typical location for air to escape from ducts is at the joints. Duct systems are built from multiple metal pieces pressed together with tight fittings and metal bands, but these joints are seldom completely airtight.

As your HVAC system warms and cools over the seasons, the ductwork expands and then contracts. Over time, this movement causes the joints to loosen, creating gaps and leaks — which is why a duct leakage test is recommended for both new and older homes in Hazlet, NJ.

Many energy auditors identify duct leakage by moving their hands along the ducts and using a small tool to check the width of joint openings. If your duct system has not been properly sealed with mastic and approved tape, it’s very likely that leakage exists.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must show under 4 CFM per 100 square feet if the air handler is installed, or 3 CFM per 100 square feet if it is not. For new construction, you must pass a duct leakage test before the home can be approved for an occupancy certificate.

If your home in Hazlet, NJ doesn’t receive a passing duct leakage result, you are likely overpaying for heating and cooling — and putting significant long-term strain on your HVAC setup. Meeting the 3–4 CFM requirement is necessary not only for meeting code standards but also for ensuring strong energy efficiency and indoor comfort.

Your technician will also recommend effective ways to fix leakage issues so you can earn a passing score, save on utilities, and improve home performance.

Local Energy Audits — affordable duct leakage test in Hazlet, NJ

Local Energy Audits proudly works with clients throughout Hazlet, NJ and nearby locations. We specialize in identifying duct leakage and energy inefficiencies using blower door tests and duct leakage tests. Whether you’re building a new home or improving an existing one, we’re here to help.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.

The Duct Leakage Test Steps Explained

A duct leakage test begins by securing duct mask tape over every duct and register on the supply and return sides.

After the registers are sealed, we connect the duct tester to the unit or to a main return.

The ducts are then depressurized to a Pascal of 25. With the ducts depressurized we can use the nanometer to get a reading of the duct leakage.

Schedule Your Duct Leakage Test in Hazlet, NJ

Ensure your HVAC system reaches optimal efficiency, satisfies code standards, and performs smoothly with expert duct leakage test in Hazlet, NJ. Whether you’re a homeowner working to improve comfort or a contractor closing out a project with a final inspection, our certified team provides fast, accurate, and affordable testing.

We use industry-standard duct blaster equipment and give on-site guidance to help you pass your test, minimize energy waste, and support the long-term health of your HVAC system.

📞 Call 888-213-3975 ✉️ Request a Quote

Serving homeowners, builders, and contractors across Hazlet, NJ with dependable and energy-efficient testing solutions.