Duct Leakage Test in Verona, NJ

How a Duct Leakage Test Is Conducted

To initiate testing, your technician will seal all supply and return registers except for the main return or air handler during a duct leakage test in Verona, NJ. A specially calibrated duct blaster fan is then secured to the opening. Its job is to depressurize the duct system, allowing air leaks to reveal themselves clearly.

The duct blaster, aided by a precision pressure sensor, accurately measures airflow and reveals duct leaks without interrupting activities in your home. A duct leakage test — sometimes identified as a duct blaster test — shows where your ducts lose air, helping you plan the right sealing approach.

duct leakage test is efficient, clean, and performed without bothering residents. Most tests in Verona, NJ are done in about 30 to 60 minutes, and the resulting enhancements can support your home’s comfort and efficiency for many years.

How to Measure Duct Leakage

Duct leakage is specified in cubic feet per minute (CFM) for each 100 square feet of conditioned space. Your technician uses a nanometer to monitor tiny pressure fluctuations that indicate how much air is leaking through the ducts. Understanding this number allows you to pinpoint problem areas, assess needed improvements, and confirm whether your home satisfies local energy code requirements in Verona, NJ.

Cost of Excessive Duct Leakage

If you’re dealing with rising utility bills, inconsistent room temperatures, or repeated HVAC issues, duct leakage could be the reason. According to ENERGY STAR, the average home loses 20% to 30% of conditioned air through leaky ducts. Outside air that’s too hot or too cold entering your system strains your HVAC, resulting in higher energy consumption and less comfort.

Overworked equipment also causes additional breakdowns and increases repair costs. Proper duct sealing helps protect and extend the long-term lifespan of your HVAC system, minimizing the need for repeated maintenance.

Duct leaks can also draw in dust, mold spores, unwanted moisture, and other harmful contaminants. This can worsen allergy flare-ups, reduce indoor air quality, and cause long-term structural deterioration behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC calls for new homes to include duct systems that are completely sealed using efficient materials such as mastic, foil tape, and insulation. But what about leaks that occur deep behind walls or ceilings out of sight?

Aerosol sealing technology (AeroSeal) allows technicians to seal leaks located inside inaccessible parts of ductwork. To carry out this method, every vent is sealed except a single access point. The HVAC system is separated, and a machine is attached to the duct system. It pressurizes the ducts and injects fine aerosol particles that seal tiny gaps and holes that typical sealing techniques miss.

This method excels at sealing small to medium leaks. However, bigger holes often must be sealed manually with mastic and tape. Technicians carry out leakage testing prior to and after aerosol sealing to observe the reduction and ensure treatment success.

Common Areas of Duct Leakage

The most common area where ducts leak air is around the joints. Ductwork uses several metal parts pressed together with tight fittings and metal bands, though these points are rarely airtight.

As your HVAC system moves through annual heating and cooling cycles, the ductwork expands and then contracts. Over time, this movement results in loose joints that create gaps and leaks — making a duct leakage test necessary for new and older homes in Verona, NJ.

Many energy auditors detect leaks by checking the duct surfaces by hand and using a small tool to measure joint gap width. If your duct system has not been sealed with mastic and approved tape, there is a high chance that leakage is occurring.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must read under 4 CFM per 100 square feet with the air handler installed, or 3 CFM per 100 square feet without the air handler. For new construction, no home can receive an occupancy certificate without first passing a duct leakage test.

If your home in Verona, NJ doesn’t pass a duct leakage test, chances are you’re paying more for heating and cooling — and adding long-term stress to your HVAC equipment. Meeting the 3–4 CFM requirement is important not just for compliance, but for safeguarding your home’s comfort and long-term energy efficiency.

Your technician will also provide professional insights on resolving leakage issues so you can achieve a passing score, lower your utility costs, and optimize home performance.

Local Energy Audits — affordable duct leakage test in Verona, NJ

Local Energy Audits is proud to serve families and builders across Verona, NJ and the surrounding local areas. We specialize in assessing duct leakage and energy inefficiencies with blower door tests and duct leakage tests. Whether it’s a new build or a current home, we’re here to support you.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.