Duct Leakage Test in Oakland, NJ

How a Duct Leakage Test Is Conducted

To initiate a duct leakage test in Oakland, NJ, your technician seals all supply and return registers, leaving only the main return or air handler open. A duct blaster, which is a specially calibrated fan, is then installed at the opening. The fan depressurizes the ducts, helping identify all points where air may be escaping.

The duct blaster uses a precision pressure sensor to monitor airflow and pinpoint leaks throughout the ductwork without interrupting your home environment. A duct leakage test — commonly called a duct blaster test — detects areas where your ducts lose air, helping you select the most efficient sealing solutions.

duct leakage test is prompt, clean, and does not interrupt residents’ activities. Most tests in Oakland, NJ are done in about 30 to 60 minutes, and the resulting enhancements can support your home’s comfort and efficiency for many years.

How to Measure Duct Leakage

Duct leakage is rated in cubic feet per minute (CFM) per 100 square feet of the home’s conditioned zone. Your technician uses a nanometer to register small pressure differences, which help calculate how much air is leaking from the ducts. Understanding this number helps you detect issues, explore potential fixes, and determine if your home aligns with local energy code requirements in Oakland, NJ.

Cost of Excessive Duct Leakage

If your energy bills are unusually high, your rooms feel unevenly heated or cooled, or your HVAC system needs frequent repairs, duct leakage could be the issue. According to ENERGY STAR, many homes lose as much as 20% to 30% of conditioned air through duct leaks. Hot or cold air entering from outside increases the workload on your HVAC system, leading to higher energy bills and a drop in comfort.

Overworked equipment also causes components to fail more often, leading to costly repairs. Proper duct sealing helps support the long-term durability of your HVAC system, lengthening its lifespan and minimizing ongoing maintenance demands.

Duct leaks can also permit dust, mold spores, extra moisture, and other airborne contaminants into the duct system. This can make allergies worse, impact indoor air quality, and result in costly structural damage behind walls or ceilings as time passes.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC requires newly built homes to install fully sealed duct systems using advanced materials like mastic, foil tape, and quality insulation. But what happens when leaks are hidden deep inside walls or ceilings?

Aerosol sealing technology (AeroSeal) makes it possible to seal leaks found deep within the ductwork. To complete this method, all vents are closed off except for one access opening. The HVAC system is isolated, and a machine is linked to the duct system. It pressurizes the ducts and releases a fine aerosolized sealant that fills small gaps and holes that traditional sealing methods cannot reach.

This method works best for small to medium leaks. However, large openings usually require traditional manual sealing using mastic and tape. Technicians perform pre- and post-aerosol sealing duct leakage tests to measure the improvement and confirm treatment effectiveness.

Common Areas of Duct Leakage

The most common leakage area in duct systems is the joints. Ductwork involves numerous metal parts pressed together with tight fittings and metal bands, but these connections are almost never fully airtight.

As your HVAC system operates in both heating and cooling modes year-round, the ducts continuously expand and contract. Over time, this movement causes the joints to loosen, opening gaps and leaks — making a duct leakage test beneficial for both new and older homes in Oakland, NJ.

Many energy auditors look for leaks by feeling the ducts and using a small tool to evaluate how wide the gaps at the joints are. If your duct system was not sealed with mastic and approved tape, there’s a high likelihood that air is leaking.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must show under 4 CFM per 100 square feet if the air handler is installed, or 3 CFM per 100 square feet if it is not. For new construction, passing a duct leakage test is required before a home can receive an occupancy certificate.

If your home in Oakland, NJ does not pass a duct leakage test, you are likely paying more than necessary for heating and cooling — and placing long-term strain on your HVAC equipment. Meeting the 3–4 CFM requirement is critical not just for code compliance, but also for defending your home’s comfort and energy performance.

Your technician will also give expert suggestions on correcting leakage issues, allowing you to pass the test, lower utility expenses, and improve your home’s overall efficiency.

Local Energy Audits — affordable duct leakage test in Oakland, NJ

Local Energy Audits proudly provides solutions to customers throughout Oakland, NJ and surrounding regions. We specialize in pinpointing duct leakage and energy inefficiencies using blower door tests and duct leakage tests. Whether you’re constructing a new house or upgrading your current one, we’re here for you.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.