Duct Leakage Test in Somers Point, NJ

How a Duct Leakage Test Is Conducted

To kick off a duct leakage test in Somers Point, NJ, your technician will block all supply and return registers while keeping the main return or air handler accessible. A calibrated duct blaster fan is then mounted to the opening. This fan creates negative pressure inside the ducts, making air leakage locations easier to find.

The duct blaster system, along with a precision pressure sensor, measures airflow and highlights leaks in the ductwork without inconveniencing you at home. A duct leakage test — widely known as a duct blaster test — pinpoints air leakage in your ducts so you can choose the best sealing methods.

duct leakage test is hassle-free, clean, and won’t interfere with residents’ daily routines. Most tests in Somers Point, NJ require only 30 to 60 minutes, yet the upgrades can improve your home’s comfort and efficiency well into the future.

How to Measure Duct Leakage

Duct leakage is reported in cubic feet per minute (CFM) per 100 square feet of conditioned home area. Your technician uses a nanometer to read small pressure variations, helping determine the volume of air escaping through the ducts. Understanding this number helps you uncover weak points, analyze opportunities for upgrades, and check whether your home follows local energy code requirements in Somers Point, NJ.

Cost of Excessive Duct Leakage

If your home has elevated utility bills, temperature imbalances, or frequent HVAC service calls, duct leakage may be responsible. According to ENERGY STAR, a large portion of homes lose between 20% and 30% of conditioned air due to leaky ducts. Hot or cold air entering from outside increases the workload on your HVAC system, leading to higher energy bills and a drop in comfort.

Overworked equipment also makes breakdowns more common and repairs more expensive. Proper duct sealing helps protect and extend the long-term lifespan of your HVAC system, minimizing the need for repeated maintenance.

Duct leaks can also allow dust, mold spores, moisture buildup, and multiple contaminants to enter the duct system. This can make allergies more severe, reduce the quality of indoor air, and produce costly structural harm behind walls or ceilings as time progresses.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC states that new homes must have duct systems sealed completely with energy-efficient products such as mastic, foil tape, and insulation. But what should you do when leaks are located deep within your walls or ceilings?

Aerosol sealing technology (AeroSeal) can identify and seal leaks that lie deep inside ductwork. To execute this method, all vents are sealed shut except a single access point. The HVAC system is isolated, and a machine is attached to the duct network. It pressurizes the ducts and releases a fine sealant mist that finds and fills small holes that traditional sealing methods cannot access.

This method excels at sealing small to medium leaks. However, bigger holes often must be sealed manually with mastic and tape. Technicians test the ducts for leakage before and after aerosol sealing to determine the reduction level and verify success.

Common Areas of Duct Leakage

The most frequent area where ducts lose air is at the joints. Ductwork consists of several metal sections pressed together with tight fittings and metal bands, yet these connections are almost never fully airtight.

As your HVAC system heats and cools throughout the year, the ducts expand and contract. Over time, this movement results in loose joints that create gaps and leaks — making a duct leakage test necessary for new and older homes in Somers Point, NJ.

Many energy auditors test for duct leakage by feeling along the ducts and using a small tool to gauge how wide the gaps are at the joints. If your duct system was never sealed using mastic and approved tape, there is a high probability that air leakage is present.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system should fall under 4 CFM per 100 square feet with the air handler, or 3 CFM per 100 square feet when the air handler is absent. For new construction, a passing duct leakage test is mandatory before a home can be granted an occupancy certificate.

If your home in Somers Point, NJ fails duct leakage test, you are probably spending unnecessarily on heating and cooling — and placing ongoing stress on your HVAC equipment. Meeting the 3–4 CFM requirement is indispensable not only for compliance purposes but for ensuring strong comfort and energy savings.

Your technician will also share expert recommendations for fixing leakage problems, helping you achieve a passing score, save on utilities, and improve home performance.

Local Energy Audits — affordable duct leakage test in Somers Point, NJ

Local Energy Audits proudly serves homeowners, contractors, and builders throughout Somers Point, NJ and nearby regions. We specialize in locating duct leakage and energy inefficiencies with our blower door and duct leakage tests. Whether it’s a new build or an existing home, we’re here to help.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.