Duct Leakage Test in Pittsgrove, NJ

Keep your HVAC system energy-efficient and up to code with accurate duct leakage test in Pittsgrove, NJ. Our certified technicians pinpoint and measure ductwork air leaks, helping homeowners and builders boost comfort, cut energy waste, and meet state compliance standards.

Why Duct Leakage Test is Important In Pittsgrove, NJ

In many jurisdictions, the 2015 IECC, International Energy Conservation Code governs single-family buildings, while the 2018 IECC applies to multi-family buildings. The change will generate several impactful implications for home builders and HVAC contractors operating statewide. A Duct Leakage Test and the mandated Blower Door Test apply to all new or renovated homes under the 2015 regulations. Did you know that ducts are one of the primary sources of air leakage in homes throughout Pennsylvania, New Jersey, and Delaware? Leaked air can result in higher utility costs, extra load on your HVAC system, and dust and insulation traveling throughout your home. This makes duct leakage test essential for both new and older homes. Continue reading to understand why duct leakage test matters and how it can benefit you.

888 213-3975

What Our Clients Say

How a Duct Leakage Test Is Conducted

To begin the process of a duct leakage test in Pittsgrove, NJ, your technician seals off all supply and return registers apart from the main return or air handler. A duct blaster, designed as a calibrated testing fan, is then attached to the duct system. Its purpose is to depressurize the ducts and uncover leak points.

The duct blaster, aided by a precision pressure sensor, accurately measures airflow and reveals duct leaks without interrupting activities in your home. A duct leakage test — often known as a duct blaster test — exposes duct air loss, allowing you to apply the most effective sealing techniques.

duct leakage test is rapid, clean, and performed without inconvenience to residents. Most tests in Pittsgrove, NJ take around 30 to 60 minutes, but the efficiency and comfort improvements can last for many years.

How to Measure Duct Leakage

Duct leakage is recorded in cubic feet per minute (CFM) per 100 square feet of the conditioned portion of the home. Your technician uses a nanometer to evaluate small pressure shifts that signal air escaping through the ducts. Understanding this number helps you uncover weak points, analyze opportunities for upgrades, and check whether your home follows local energy code requirements in Pittsgrove, NJ.

Cost of Excessive Duct Leakage

If your home has elevated utility bills, temperature imbalances, or frequent HVAC service calls, duct leakage may be responsible. According to ENERGY STAR, the average home loses 20% to 30% of conditioned air through leaky ducts. Hot or cold outside air entering your system forces your HVAC system to work harder, driving up energy costs and reducing comfort.

Overworked equipment also produces more frequent issues that require costly repairs. Proper duct sealing helps keep your HVAC system healthy over the long run, prolonging its lifespan and lowering continued maintenance needs.

Duct leaks can also permit dust, mold spores, extra moisture, and other airborne contaminants into the duct system. This can make allergies more severe, reduce the quality of indoor air, and produce costly structural harm behind walls or ceilings as time progresses.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC instructs that new homes incorporate fully sealed duct systems using high-efficiency materials, including mastic, foil tape, and insulation. But what if some leaks are hidden within the depths of your walls or ceilings?

Aerosol sealing technology (AeroSeal) enables effective sealing of leaks hidden inside ducts. To execute this method, all vents are sealed shut except a single access point. The HVAC system is isolated, and a machine is attached to the duct network. It pressurizes the ducts and pushes a fine aerosol sealant through them, sealing small holes that ordinary sealing methods can’t reach.

This method seals small to medium leaks effectively. However, large gaps may still call for manual sealing using mastic and tape. Technicians complete before-and-after duct leakage tests to measure leakage reduction and ensure the aerosol sealing was effective.

Common Areas of Duct Leakage

The most typical place where ducts leak air is at their joints. Ductwork is built from multiple metal sections pressed tightly with fittings and metal bands, yet these joints are rarely airtight.

As your HVAC system shifts between hot and cold cycles all year long, the ductwork expands and contracts. Over time, this movement weakens the joints, creating gaps and leaks — a key reason duct leakage test is recommended for new and older homes in Pittsgrove, NJ.

Many energy auditors inspect duct leakage by feeling the ducts and using a small tool to determine how wide the gaps are between joints. If your duct system does not include sealing with mastic and approved tape, leakage is highly likely.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must show under 4 CFM per 100 square feet if the air handler is installed, or 3 CFM per 100 square feet if it is not. For new construction, the duct leakage test must be passed prior to the home being approved for an occupancy certificate.

If your home in Pittsgrove, NJ doesn’t receive a passing duct leakage result, you are likely overpaying for heating and cooling — and putting significant long-term strain on your HVAC setup. Meeting the 3–4 CFM requirement is vital not only for satisfying code rules but also for preserving your home’s comfort and energy performance.

Your technician will also offer professional recommendations to tackle leakage issues so you can secure a passing score, reduce utility costs, and strengthen home performance.

Local Energy Audits — affordable duct leakage test in Pittsgrove, NJ

Local Energy Audits proudly delivers services across Pittsgrove, NJ and the surrounding neighborhoods. We specialize in identifying and addressing duct leakage and energy inefficiencies using blower door tests and duct leakage tests. Whether you’re constructing a new home or optimizing an existing one, we’re here to help.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.

The Duct Leakage Test Steps Explained

A duct leakage test begins by sealing all the ducts and registers with duct mask tape on both the supply and return side.

After the registers are sealed we attached the duct tester to either the unit itself or a main return.

The ducts are then depressurized to a level of 25 Pascals. Once depressurized, the nanometer provides an accurate duct leakage reading.

Schedule Your Duct Leakage Test in Pittsgrove, NJ

Ensure your HVAC system continues to perform efficiently, meets compliance, and runs at its best with specialized duct leakage test in Pittsgrove, NJ. Whether you’re a homeowner working to improve comfort or a contractor closing out a project with a final inspection, our certified team provides fast, accurate, and affordable testing.

We use industry-standard duct blaster equipment and offer direct on-site guidance to help you pass your test, lower energy waste, and protect your HVAC system’s long-term health.

📞 Call 888-213-3975 ✉️ Request a Quote

Serving homeowners, builders, and contractors across Pittsgrove, NJ with dependable and energy-efficient testing solutions.