Duct Leakage Test in Hardyston, NJ

How a Duct Leakage Test Is Conducted

To start conducting a duct leakage test in Hardyston, NJ, the technician seals all supply and return registers other than the main return or the air handler. A specially calibrated fan known as a duct blaster is then put in place at the opening. It depressurizes the ductwork so escaping air can be accurately identified.

The duct blaster and its precision pressure sensor work together to measure airflow and detect duct leaks without causing any disruption in your home. A duct leakage test — sometimes identified as a duct blaster test — shows where your ducts lose air, helping you plan the right sealing approach.

duct leakage test is efficient, clean, and performed without bothering residents. Most tests in Hardyston, NJ take 30 to 60 minutes to complete, and the benefits to comfort and efficiency can endure for years.

How to Measure Duct Leakage

Duct leakage is measured using cubic feet per minute (CFM) per 100 square feet of conditioned floor area. Your technician uses a nanometer to evaluate small pressure shifts that signal air escaping through the ducts. Understanding this number allows you to highlight problem zones, explore improvement possibilities, and confirm compliance with local energy code requirements in Hardyston, NJ.

Cost of Excessive Duct Leakage

If you’re facing higher energy bills, uneven heating or cooling, or recurring HVAC repairs, duct leakage could be to blame. According to ENERGY STAR, the average home loses 20% to 30% of conditioned air through leaky ducts. Hot or cold outside air creeping into your system forces the HVAC to work inefficiently, increasing energy spending and reducing comfort.

Overworked equipment also accelerates wear and tear, resulting in more breakdowns and costly repairs. Proper duct sealing helps ensure the long-term stability of your HVAC system, extending its lifespan and reducing future maintenance work.

Duct leaks can also pull dust, mold spores, excess moisture, and various contaminants into the duct system. This can negatively influence allergies, weaken indoor air quality, and lead to expensive long-term damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC mandates that new homes include fully sealed duct systems built with energy-efficient materials like mastic, foil tape, and proper insulation. But what about leaks located deep within walls or ceilings?

Aerosol sealing technology (AeroSeal) gives technicians a way to reach concealed duct leaks without opening walls or ceilings. To execute this method, all vents are sealed shut except a single access point. The HVAC system is isolated, and a machine is attached to the duct network. It pressurizes the ducts and emits a fine aerosolized sealant designed to fill small leaks unreachable with standard sealing.

This method works efficiently for small to medium leaks. However, larger gaps usually require manual sealing using mastic and tape. Technicians run a duct leakage test before and after aerosol sealing to quantify the reduction in leakage and verify the success of the process.

Common Areas of Duct Leakage

The most usual spot for duct air leakage is the joints. Ductwork is composed of various metal pieces pressed together using tight fittings and metal bands, but these seals are hardly ever fully airtight.

As your HVAC system regulates temperatures through the seasons, the ducts expand when heated and contract when cooled. Over time, this movement weakens joint connections, producing gaps and leaks — making duct leakage test essential for both new and older homes in Hardyston, NJ.

Many energy auditors detect duct leakage by physically checking the ducts and using a small tool to assess the width of joint gaps. If your duct system isn’t sealed with mastic and approved tape, there’s a good chance that leaks are occurring.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must read under 4 CFM per 100 square feet with the air handler installed, or 3 CFM per 100 square feet without the air handler. For new construction, homes are required to pass a duct leakage test before an occupancy certificate can be issued.

If your home in Hardyston, NJ fails duct leakage test, you are probably spending unnecessarily on heating and cooling — and placing ongoing stress on your HVAC equipment. Meeting the 3–4 CFM requirement is key not only for staying code-compliant but for maintaining energy efficiency and consistent comfort in your home.

Your technician will also provide expert recommendations on how to address leakage issues so you can achieve a passing score, lower your utility bills, and improve your home’s overall performance.

Local Energy Audits — affordable duct leakage test in Hardyston, NJ

Local Energy Audits is proud to work with customers in Hardyston, NJ and all nearby areas. We specialize in evaluating duct leakage and energy inefficiencies with blower door and duct leakage tests. Whether you’re developing a new home or enhancing an older one, we’re here to help.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.