Duct Leakage Test in Mendham borough, NJ

How a Duct Leakage Test Is Conducted

To start a duct leakage test in Mendham borough, NJ, the technician will close and seal every supply and return register except the main return or air handler. A specially calibrated device known as a duct blaster is then attached to the duct opening. Its purpose is to depressurize the system so that escaping air can be detected.

The duct blaster joins forces with a precision pressure sensor to monitor airflow and pinpoint leak points in the ducts without disturbing your home. A duct leakage test — sometimes called a duct blaster test — reveals where your ducts are losing air so you can determine the most effective sealing solutions.

duct leakage test is swift, clean, and carried out with no disturbance to residents. Most tests in Mendham borough, NJ are wrapped up in 30 to 60 minutes, with improvements that continue to boost comfort and efficiency for years.

How to Measure Duct Leakage

Duct leakage is assessed using cubic feet per minute (CFM) per 100 square feet of conditioned space. Your technician uses a nanometer to measure tiny pressure changes, revealing how much air is escaping through the ducts. Understanding this number allows you to pinpoint problem areas, assess needed improvements, and confirm whether your home satisfies local energy code requirements in Mendham borough, NJ.

Cost of Excessive Duct Leakage

If you observe rising utility costs, temperature swings in different rooms, or regular HVAC breakdowns, duct leakage may be involved. According to ENERGY STAR, the typical home loses between 20% and 30% of its conditioned air due to duct leaks. Outside hot or cold air leaking into your system puts extra strain on your HVAC unit, raising energy bills and decreasing comfort.

Overworked equipment also causes components to fail more often, leading to costly repairs. Proper duct sealing helps uphold the long-term performance of your HVAC system, stretching its lifespan and decreasing routine maintenance demands.

Duct leaks can also allow dust, mold spores, excess moisture, and other contaminants into the duct system. This can make allergies worse, impact indoor air quality, and result in costly structural damage behind walls or ceilings as time passes.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC requires new homes to use fully sealed duct systems crafted from up-to-date, efficient materials such as mastic, foil tape, and insulation. But what about leaks that are hidden far behind walls or ceilings?

Aerosol sealing technology (AeroSeal) is an effective solution for reaching hidden ductwork leaks. To set up this method, all vents are sealed off except for a single access point. The HVAC system is isolated, and a machine is fitted to the duct system. It pressurizes the ducts and applies a fine aerosol sealant that fills tiny openings where standard sealing cannot reach.

This method excels at sealing small to medium leaks. However, bigger holes often must be sealed manually with mastic and tape. Technicians test the ducts for leakage before and after aerosol sealing to determine the reduction level and verify success.

Common Areas of Duct Leakage

The most frequent source of duct air leakage is the joints. Ductwork uses many metal pieces pressed together with tight fittings and metal bands, but these joining points are rarely airtight.

As your HVAC system operates in varying temperatures across the year, the ducts undergo expansion and contraction. Over time, this movement leads to joint loosening, generating gaps and leaks — a clear reason duct leakage test is recommended for new and older homes in Mendham borough, NJ.

Many energy auditors verify duct leakage by feeling around the ducts and using a small tool to assess the opening size at the joints. If your duct system has not been properly sealed with mastic and approved tape, it’s very likely that leakage exists.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system should come out under 4 CFM per 100 square feet in tests with the air handler, or 3 CFM per 100 square feet without the air handler. For new construction, the duct leakage test must be passed prior to the home being approved for an occupancy certificate.

If your home in Mendham borough, NJ fails duct leakage test, you are probably spending unnecessarily on heating and cooling — and placing ongoing stress on your HVAC equipment. Meeting the 3–4 CFM requirement is fundamental not only for code adherence but for boosting your home’s long-term efficiency and comfort.

Your technician will also advise you on the best ways to address leakage issues so you can pass the test, reduce utility bills, and enhance your home’s efficiency.

Local Energy Audits — affordable duct leakage test in Mendham borough, NJ

Local Energy Audits proudly works with clients throughout Mendham borough, NJ and nearby locations. We specialize in pinpointing duct leakage and energy inefficiencies using blower door tests and duct leakage tests. Whether you’re constructing a new house or upgrading your current one, we’re here for you.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.