Duct Leakage Test in New Milford borough, NJ

How a Duct Leakage Test Is Conducted

To begin a duct leakage test in New Milford borough, NJ, your technician will seal off all supply and return registers except for the main return or the air handler. A specially calibrated duct blaster is then installed onto the opening. The fan lowers the pressure inside the ducts, helping reveal any leakage points.

The duct blaster joins forces with a precision pressure sensor to monitor airflow and pinpoint leak points in the ducts without disturbing your home. A duct leakage test — sometimes called a duct blaster test — reveals where your ducts are losing air so you can determine the most effective sealing solutions.

duct leakage test is efficient, clean, and performed without bothering residents. Most tests in New Milford borough, NJ are completed within 30 to 60 minutes, and the improvements can benefit your home’s comfort and efficiency for years.

How to Measure Duct Leakage

Duct leakage is monitored in cubic feet per minute (CFM) per 100 square feet of the conditioned sections of the home. Your technician uses a nanometer to measure tiny pressure changes, revealing how much air is escaping through the ducts. Understanding this number helps you detect inefficiencies, assess needed upgrades, and ensure your home complies with local energy code requirements in New Milford borough, NJ.

Cost of Excessive Duct Leakage

If you’re encountering increased energy bills, temperature inconsistencies, or constant HVAC repairs, duct leakage could be the source. According to ENERGY STAR, the average home loses 20% to 30% of conditioned air through leaky ducts. When hot or cold outside air enters your system, your HVAC has to work harder, increasing energy costs and lowering overall comfort.

Overworked equipment also accelerates wear and tear, resulting in more breakdowns and costly repairs. Proper duct sealing helps protect the long-term performance of your HVAC system, increasing its lifespan and lowering future maintenance requirements.

Duct leaks can also cause dust, mold spores, and excess moisture — along with other contaminants — to infiltrate the duct system. This can heighten allergy issues, compromise indoor air quality, and slowly cause expensive structural damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC requires all newly constructed homes to have fully sealed ductwork with modern, energy-saving materials such as mastic, foil tape, and insulation. But what if some leaks are hidden within the depths of your walls or ceilings?

Aerosol sealing technology (AeroSeal) is designed to reach and seal hidden gaps throughout the duct system. To perform the technique, all vents are sealed except a single access opening. The HVAC system is isolated, and a machine is hooked into the duct system. It pressurizes the ducts and injects fine aerosol particles that seal tiny gaps and holes that typical sealing techniques miss.

This method is very effective for minor to moderate leaks. However, substantial openings may still need traditional sealing with mastic and tape. Technicians complete a duct leakage test before and after aerosol sealing to track leakage reduction and confirm the treatment’s success.

Common Areas of Duct Leakage

The most typical place for ducts to lose air is at the joints. Ductwork consists of different metal sections pressed together with tight fittings and metal bands, yet these joints are not usually airtight.

As your HVAC system shifts between hot and cold cycles all year long, the ductwork expands and contracts. Over time, this movement shifts and loosens the joints, resulting in gaps and leaks — which is why all homes in New Milford borough, NJ, new or older, benefit from duct leakage test.

Many energy auditors check for leaks by feeling along the ductwork and using a small tool to gauge the size of gaps between joints. If your duct system lacks sealing with mastic and approved tape, there is a strong chance that leakage is present.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system has to measure below 4 CFM per 100 square feet with the air handler installed, or 3 CFM per 100 square feet without the air handler. For new construction, obtaining an occupancy certificate requires passing a duct leakage test first.

If your home in New Milford borough, NJ doesn’t pass a duct leakage test, chances are you’re paying more for heating and cooling — and adding long-term stress to your HVAC equipment. Meeting the 3–4 CFM requirement is significant not only for meeting local code but also for maintaining optimal comfort and efficiency in your home.

Your technician will also share expert solutions for tackling leakage problems so you can pass the test, cut down utility expenses, and improve overall comfort and efficiency.

Local Energy Audits — affordable duct leakage test in New Milford borough, NJ

Local Energy Audits proudly serves homeowners, contractors, and builders throughout New Milford borough, NJ and nearby regions. We specialize in diagnosing duct leakage and energy inefficiencies through blower door and duct leakage test. Whether your home is new or existing, we’re ready to help.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.