Duct Leakage Test in Stone Harbor, NJ

How a Duct Leakage Test Is Conducted

To initiate a duct leakage test in Stone Harbor, NJ, your technician seals all supply and return registers, leaving only the main return or air handler open. A specially calibrated fan, known as a duct blaster, is then attached to the opening. The purpose of this fan is to depressurize the duct system, creating the ideal conditions to identify where air is escaping.

The duct blaster functions with a precision pressure sensor to analyze airflow and spot leaks in the duct system without affecting your home’s comfort. A duct leakage test — often described as a duct blaster test — identifies leaking areas in your ducts so you can determine the most efficient sealing fix.

duct leakage test is rapid, clean, and performed without inconvenience to residents. Most tests in Stone Harbor, NJ take only 30 to 60 minutes, yet the comfort and efficiency gains can last for years.

How to Measure Duct Leakage

Duct leakage is determined in cubic feet per minute (CFM) for every 100 square feet of conditioned interior space. Your technician uses a nanometer to read small pressure variations, helping determine the volume of air escaping through the ducts. Understanding this number helps you locate trouble spots, review possible upgrades, and see if your home complies with local energy code requirements in Stone Harbor, NJ.

Cost of Excessive Duct Leakage

If elevated utility bills, shifting temperatures, or repeated HVAC issues occur in your home, duct leakage may be the factor behind them. According to ENERGY STAR, homes with leaky ducts routinely lose 20% to 30% of conditioned air. When outdoor temperatures enter your system, the HVAC must work harder to compensate, resulting in higher energy costs and reduced comfort.

Overworked equipment also triggers more mechanical failures and costly service calls. Proper duct sealing helps protect the long-term performance of your HVAC system, increasing its lifespan and lowering future maintenance requirements.

Duct leaks can also introduce dust, mold spores, moisture, and additional contaminants into the duct system. This can trigger more severe allergies, diminish indoor air quality, and create expensive structural problems behind walls or ceilings over time.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC specifies that newly constructed homes must use fully sealed duct systems with modern, efficient materials such as mastic, foil tape, and insulation. But what about leaks that are hidden far behind walls or ceilings?

Aerosol sealing technology (AeroSeal) is designed to reach and seal hidden gaps throughout the duct system. To execute this method, all vents are sealed shut except a single access point. The HVAC system is isolated, and a machine is attached to the duct network. It pressurizes the ducts and circulates a fine aerosolized sealant that locates and fills tiny leaks beyond the reach of typical sealing.

This method is great for handling small to medium leaks. However, larger holes often require manual sealing with mastic and tape. Technicians carry out a duct leakage test before and after aerosol sealing to assess how much leakage has improved and ensure the treatment was effective.

Common Areas of Duct Leakage

The most typical place for ducts to lose air is at the joints. Ductwork consists of different metal sections pressed together with tight fittings and metal bands, yet these joints are not usually airtight.

As your HVAC system transitions between warm and cool air throughout the year, the ducts expand and contract. Over time, this movement loosens the joints, causing gaps and leaks — which is why both new and older homes in Stone Harbor, NJ should consider a duct leakage test.

Many energy auditors detect leaks by checking the duct surfaces by hand and using a small tool to measure joint gap width. If your duct system has not been sealed with mastic and approved tape, there is a high chance that leakage is occurring.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must come in under 4 CFM per 100 square feet with the air handler, or 3 CFM per 100 square feet when the air handler is removed. For new construction, passing the duct leakage test is a necessary step before securing an occupancy certificate.

If your home in Stone Harbor, NJ fails a duct leakage test, you are probably spending more than you should on heating and cooling — while also putting long-term stress on your HVAC system. Meeting the 3–4 CFM requirement is essential not only for following building code, but for keeping your home comfortable and energy-efficient.

Your technician will also offer specialized recommendations to repair leakage issues so you can meet passing requirements, reduce utility bills, and improve your home’s performance.

Local Energy Audits — affordable duct leakage test in Stone Harbor, NJ

Local Energy Audits proudly serves customers throughout Stone Harbor, NJ and surrounding areas. We specialize in finding duct leakage and energy inefficiencies through blower door tests and duct leakage tests. Whether you’re constructing a new home or upgrading an older one, we’re ready to assist.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.