Duct Leakage Test in Longport borough, NJ

Enhance your HVAC system’s efficiency and satisfy energy regulations through precise duct leakage test in Longport borough, NJ. Our certified technicians detect and measure air leakage in ductwork, supporting homeowners and builders in improving comfort, minimizing wasted energy, and meeting state requirements.

Why Duct Leakage Test is Important In Longport borough, NJ

Many states and municipalities enforce the 2015 IECC, International Energy Conservation Code for single-family properties and the 2018 International Energy Conservation Code for multi-family developments. The change will set in motion important implications for home builders and HVAC contractors who operate in the state. A Duct Leakage Test together with a Blower Door Test has become mandatory for any newly constructed or remodeled home under the 2015 code. Did you know that improperly sealed ducts account for a major portion of air leakage in homes across Pennsylvania, New Jersey, and Delaware? Leaked air can lead to rising energy bills, added strain on your HVAC system, and unwanted insulation and dust spreading through your home. This makes duct leakage test necessary for homeowners with either older or newly built homes. Read ahead to see why duct leakage test is important and what you gain from it.

888 213-3975

What Our Clients Say

How a Duct Leakage Test Is Conducted

To conduct a proper duct leakage test in Longport borough, NJ, your technician first seals all supply and return registers except the main return or air handler. A specially calibrated device known as a duct blaster is then attached to the duct opening. Its purpose is to depressurize the system so that escaping air can be detected.

The duct blaster operates alongside a precision pressure sensor to track airflow and identify duct leaks without disrupting your home. A duct leakage test — often referred to as a duct blaster test — identifies air loss in your ducts, allowing you to find the most effective ways to seal them.

duct leakage test is fast, tidy, and causes no disruption for residents. Most tests in Longport borough, NJ are done within 30 to 60 minutes, with improvements that strengthen comfort and efficiency for years to come.

How to Measure Duct Leakage

Duct leakage is rated in cubic feet per minute (CFM) per 100 square feet of the home’s conditioned zone. Your technician uses a nanometer to detect pressure variations, helping quantify the amount of duct leakage. Understanding this number helps you identify problem areas, evaluate potential improvements, and determine whether your home meets local energy code requirements in Longport borough, NJ.

Cost of Excessive Duct Leakage

If you’re struggling with expensive utility bills, inconsistent indoor temperatures, or continual HVAC problems, duct leakage might be the culprit. According to ENERGY STAR, homes across the country lose 20% to 30% of their conditioned air through duct leakage. Hot or cold air entering from outside increases the workload on your HVAC system, leading to higher energy bills and a drop in comfort.

Overworked equipment also results in more frequent breakdowns and expensive repair bills. Proper duct sealing helps maintain the long-term health of your HVAC system, extending its lifespan and reducing ongoing maintenance needs.

Duct leaks can also let in dust, mold spores, added moisture, and other harmful contaminants. This can worsen allergy conditions, affect indoor air quality, and result in costly damage forming behind walls or ceilings over time.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC mandates fully sealed duct systems in new homes, made from energy-efficient materials like mastic, foil tape, and proper insulation. But what happens when leaks are hidden deep inside walls or ceilings?

Aerosol sealing technology (AeroSeal) helps target hard-to-reach openings deep within ducts. To begin this method, every vent is sealed except for one access opening. The HVAC unit is isolated, and a machine is installed onto the duct system. It pressurizes the ducts and releases a fine aerosolized sealant that fills small gaps and holes that traditional sealing methods cannot reach.

This method is ideal for small to medium leaks. However, any large openings will still need manual sealing with mastic and tape. Technicians use before-and-after duct leakage tests to measure improvement and make sure the aerosol sealing process was successful.

Common Areas of Duct Leakage

The most common leakage area in duct systems is the joints. Ductwork involves numerous metal parts pressed together with tight fittings and metal bands, but these connections are almost never fully airtight.

As your HVAC system delivers heat and cooling across different seasons, the ducts constantly expand and contract. Over time, this movement makes joints shift and loosen, forming gaps and leaks — which is why a duct leakage test is advised for homes old and new in Longport borough, NJ.

Many energy auditors check duct leakage by feeling around the ducts and using a small tool to test the width of gaps between joints. If your duct system wasn’t properly sealed using mastic and approved tape, air leakage is very likely occurring.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system needs to register under 4 CFM per 100 square feet with the air handler attached, or 3 CFM per 100 square feet without it attached. For new construction, a passing duct leakage test is essential before the home can qualify for an occupancy certificate.

If your home in Longport borough, NJ doesn’t achieve a passing duct leakage score, you’re likely overspending on heating and cooling — and putting extended strain on your HVAC unit. Meeting the 3–4 CFM requirement is needed not only for passing inspections, but also for improving home comfort and energy efficiency.

Your technician will also provide expert insights into correcting leakage issues so you can meet passing standards, lower your utility expenses, and improve overall home performance.

Local Energy Audits — affordable duct leakage test in Longport borough, NJ

Local Energy Audits proudly serves customers throughout Longport borough, NJ and surrounding areas. We specialize in evaluating duct leakage and energy inefficiencies with blower door and duct leakage tests. Whether you’re developing a new home or enhancing an older one, we’re here to help.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.

The Duct Leakage Test Steps Explained

A duct leakage test begins with the technician sealing all ducts and registers using duct mask tape across the supply and return sides.

After the registers are sealed, we install the duct tester on the unit or on a main return.

The ducts are then depressurized to a Pascal of 25. With the ducts depressurized we can use the nanometer to get a reading of the duct leakage.

Schedule Your Duct Leakage Test in Longport borough, NJ

Ensure your HVAC system delivers maximum efficiency, full compliance, and top performance through professional duct leakage test in Longport borough, NJ. Whether you’re a homeowner improving home comfort or a contractor finishing required inspections, our certified team delivers fast, accurate, and affordable testing.

We use industry-standard duct blaster equipment and supply on-site guidance to help you pass your test, reduce energy loss, and maintain the long-term health of your HVAC system.

📞 Call 888-213-3975 ✉️ Request a Quote

Serving homeowners, builders, and contractors across Longport borough, NJ with dependable and energy-efficient testing solutions.