Duct Leakage Test in Hamilton township (Atlantic), NJ

How a Duct Leakage Test Is Conducted

To conduct a proper duct leakage test in Hamilton township (Atlantic), NJ, your technician first seals all supply and return registers except the main return or air handler. A specially calibrated fan known as a duct blaster is then put in place at the opening. It depressurizes the ductwork so escaping air can be accurately identified.

The duct blaster teams up with a precision pressure sensor to measure airflow accurately and locate duct leaks without affecting your home. A duct leakage test — also called a duct blaster test — locates the points where duct air escapes, helping you implement the right sealing solution.

duct leakage test is swift, clean, and carried out with no disturbance to residents. Most tests in Hamilton township (Atlantic), NJ take between 30 and 60 minutes, and the improvements they deliver can elevate comfort and efficiency for years ahead.

How to Measure Duct Leakage

Duct leakage is rated in cubic feet per minute (CFM) per 100 square feet of the home’s conditioned zone. Your technician uses a nanometer to pick up minor pressure shifts that indicate the level of air leakage within the ducts. Understanding this number helps you spot leakage issues, evaluate corrective measures, and determine if your home is meeting local energy code requirements in Hamilton township (Atlantic), NJ.

Cost of Excessive Duct Leakage

If you’re facing higher energy bills, uneven heating or cooling, or recurring HVAC repairs, duct leakage could be to blame. According to ENERGY STAR, homes across the country lose 20% to 30% of their conditioned air through duct leakage. Air from outside—whether hot or cold—entering your system forces your HVAC to work harder, increasing utility bills and reducing indoor comfort.

Overworked equipment also leads to more breakdowns and costly repairs. Proper duct sealing helps protect the long-term performance of your HVAC system, increasing its lifespan and lowering future maintenance requirements.

Duct leaks can also enable dust, mold spores, elevated moisture, and unwanted contaminants to infiltrate the duct system. This can negatively influence allergies, weaken indoor air quality, and lead to expensive long-term damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC requires newly built homes to install fully sealed duct systems using advanced materials like mastic, foil tape, and quality insulation. But what happens when leaks are trapped deep inside wall or ceiling cavities?

Aerosol sealing technology (AeroSeal) is one way to reach hidden openings inside ductwork. To initiate this method, technicians seal every vent except one access point. The HVAC system is isolated, and a machine is connected to the ductwork. It pressurizes the ducts and sends a fine aerosol sealant through the system, closing small gaps that normal sealing approaches can’t reach.

This method is very effective for minor to moderate leaks. However, substantial openings may still need traditional sealing with mastic and tape. Technicians complete before-and-after duct leakage tests to measure leakage reduction and ensure the aerosol sealing was effective.

Common Areas of Duct Leakage

The most usual spot for duct air leakage is the joints. Ductwork is composed of various metal pieces pressed together using tight fittings and metal bands, but these seals are hardly ever fully airtight.

As your HVAC system moves through annual heating and cooling cycles, the ductwork expands and then contracts. Over time, this movement leads the joints to loosen, resulting in gaps and leaks — making a duct leakage test important for new and older homes in Hamilton township (Atlantic), NJ.

Many energy auditors look for duct leakage by running their hands along the ducts and using a small tool to measure the width of gaps at the joints. If your duct system is missing mastic and approved tape sealing, there’s a significant chance that air leakage is happening.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system should stay under 4 CFM per 100 square feet with the air handler attached, or 3 CFM per 100 square feet without it. For new construction, no home can receive an occupancy certificate without first passing a duct leakage test.

If your home in Hamilton township (Atlantic), NJ cannot achieve a passing duct leakage score, you are likely wasting money on heating and cooling — and increasing wear on your HVAC system over time. Meeting the 3–4 CFM requirement is fundamental not only for code adherence but for boosting your home’s long-term efficiency and comfort.

Your technician will also recommend effective ways to fix leakage issues so you can earn a passing score, save on utilities, and improve home performance.

Local Energy Audits — affordable duct leakage test in Hamilton township (Atlantic), NJ

Local Energy Audits proudly covers Hamilton township (Atlantic), NJ and all nearby towns. We specialize in locating duct leakage and energy inefficiencies with our blower door and duct leakage tests. Whether it’s a new build or an existing home, we’re here to help.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.