Duct Leakage Test in Evesham township, NJ

How a Duct Leakage Test Is Conducted

To prepare for a duct leakage test in Evesham township, NJ, the technician seals every supply and return register, leaving only the main return or air handler unsealed. A specially calibrated duct blaster fan is then secured to the opening. Its job is to depressurize the duct system, allowing air leaks to reveal themselves clearly.

The duct blaster pairs with a precision pressure sensor to measure airflow and identify leak locations in the ducts without disrupting your home. A duct leakage test — often referred to as a duct blaster test — identifies air loss in your ducts, allowing you to find the most effective ways to seal them.

duct leakage test is easy, clean, and unobtrusive for residents in the home. Most tests in Evesham township, NJ are completed in roughly 30 to 60 minutes, and the resulting enhancements can support your home’s comfort and efficiency long-term.

How to Measure Duct Leakage

Duct leakage is defined in cubic feet per minute (CFM) per 100 square feet of conditioned space within the structure. Your technician uses a nanometer to detect pressure variations, helping quantify the amount of duct leakage. Understanding this number allows you to highlight problem zones, explore improvement possibilities, and confirm compliance with local energy code requirements in Evesham township, NJ.

Cost of Excessive Duct Leakage

If your home has elevated utility bills, temperature imbalances, or frequent HVAC service calls, duct leakage may be responsible. According to ENERGY STAR, a large portion of homes lose between 20% and 30% of conditioned air due to leaky ducts. Hot or cold outside air creeping into your system forces the HVAC to work inefficiently, increasing energy spending and reducing comfort.

Overworked equipment also causes components to fail more often, leading to costly repairs. Proper duct sealing helps maintain the long-term health of your HVAC system, extending its lifespan and reducing ongoing maintenance needs.

Duct leaks can also create openings for dust, mold spores, moisture, and various contaminants to enter the duct system. This can worsen allergy reactions, negatively affect indoor air quality, and contribute to costly hidden structural damage over the years.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC instructs that new homes incorporate fully sealed duct systems using high-efficiency materials, including mastic, foil tape, and insulation. But what happens when air leaks are concealed deep in the walls or ceilings?

Aerosol sealing technology (AeroSeal) gives technicians a way to reach concealed duct leaks without opening walls or ceilings. To perform this method, all vents are sealed off except for one access point. The HVAC system is isolated, and a machine is connected to the duct system. It pressurizes the ducts and distributes a fine aerosolized sealant that seals small openings traditional methods cannot reach.

This method is effective at treating small to medium leaks. However, big openings may still need to be addressed with manual mastic-and-tape sealing. Technicians conduct duct leakage test before and after aerosol sealing to see how much the leakage dropped and ensure the treatment worked properly.

Common Areas of Duct Leakage

The most typical place for ducts to lose air is at the joints. Ductwork consists of different metal sections pressed together with tight fittings and metal bands, yet these joints are not usually airtight.

As your HVAC system adjusts temperatures throughout the year, the ducts go through expansion and contraction. Over time, this movement leads the joints to loosen, resulting in gaps and leaks — making a duct leakage test important for new and older homes in Evesham township, NJ.

Many energy auditors test for duct leakage by feeling along the ducts and using a small tool to gauge how wide the gaps are at the joints. If your duct system has not been properly sealed with mastic and approved tape, it’s very likely that leakage exists.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system should measure under 4 CFM per 100 square feet with the air handler installed, or 3 CFM per 100 square feet without the air handler installed. For new construction, a passing duct leakage test is a required step before final occupancy certification can be awarded.

If your home in Evesham township, NJ does not pass a duct leakage test, you are likely paying more than necessary for heating and cooling — and placing long-term strain on your HVAC equipment. Meeting the 3–4 CFM requirement is vital not only for satisfying code rules but also for preserving your home’s comfort and energy performance.

Your technician will also share expert solutions for tackling leakage problems so you can pass the test, cut down utility expenses, and improve overall comfort and efficiency.

Local Energy Audits — affordable duct leakage test in Evesham township, NJ

Local Energy Audits proudly supports customers throughout Evesham township, NJ and the areas nearby. We specialize in identifying and addressing duct leakage and energy inefficiencies using blower door tests and duct leakage tests. Whether you’re constructing a new home or optimizing an existing one, we’re here to help.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.