Duct Leakage Test in Barnegat township, NJ

How a Duct Leakage Test Is Conducted

To kick off a duct leakage test in Barnegat township, NJ, your technician will block all supply and return registers while keeping the main return or air handler accessible. A specially calibrated device known as a duct blaster is then attached to the duct opening. Its purpose is to depressurize the system so that escaping air can be detected.

The duct blaster and its precision pressure sensor work together to measure airflow and detect duct leaks without causing any disruption in your home. A duct leakage test — sometimes identified as a duct blaster test — shows where your ducts lose air, helping you plan the right sealing approach.

duct leakage test is simple, clean, and minimally invasive for residents. Most tests in Barnegat township, NJ require only 30 to 60 minutes, yet the upgrades can improve your home’s comfort and efficiency well into the future.

How to Measure Duct Leakage

Duct leakage is rated in cubic feet per minute (CFM) per 100 square feet of the home’s conditioned zone. Your technician uses a nanometer to detect minimal pressure variations, revealing the amount of air leakage occurring in the duct system. Understanding this number helps you uncover weak points, analyze opportunities for upgrades, and check whether your home follows local energy code requirements in Barnegat township, NJ.

Cost of Excessive Duct Leakage

If your energy bills are unusually high, your rooms feel unevenly heated or cooled, or your HVAC system needs frequent repairs, duct leakage could be the issue. According to ENERGY STAR, a large portion of homes lose between 20% and 30% of conditioned air due to leaky ducts. When your system pulls in hot or cold outdoor air, the HVAC unit has to work harder, driving up energy usage and reducing comfort indoors.

Overworked equipment also creates more wear, leading to breakdowns and costly fixes. Proper duct sealing helps support your HVAC system’s long-term operation, increasing its lifespan and lowering frequent maintenance needs.

Duct leaks can also introduce dust, mold spores, excess humidity, and other contaminants into the duct system. This can increase allergy discomfort, degrade indoor air quality, and eventually cause expensive structural issues behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC requires newly built homes to install fully sealed duct systems using advanced materials like mastic, foil tape, and quality insulation. But what about leaks that occur deep behind walls or ceilings out of sight?

Aerosol sealing technology (AeroSeal) enables effective sealing of leaks hidden inside ducts. To carry out the procedure, technicians seal off all vents except one access point. The HVAC system is isolated, and a machine is linked to the duct system. It pressurizes the ducts and releases a fine sealant mist that finds and fills small holes that traditional sealing methods cannot access.

This method works best for small to medium leaks. However, large openings usually require traditional manual sealing using mastic and tape. Technicians run a duct leakage test before and after aerosol sealing to quantify the reduction in leakage and verify the success of the process.

Common Areas of Duct Leakage

The most usual area for air leakage in ducts is at the joints. Ductwork includes various metal pieces pressed together using tight fittings and metal bands, but these connections are hardly ever airtight.

As your HVAC system heats and cools during seasonal changes, the ductwork expands and then contracts. Over time, this movement causes the joints to loosen, creating gaps and leaks — which is why a duct leakage test is recommended for both new and older homes in Barnegat township, NJ.

Many energy auditors evaluate duct leakage by feeling around the duct system and using a small tool to check the size of joint gaps. If your duct system has not received sealing with mastic and approved tape, leakage is very probable.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must show under 4 CFM per 100 square feet if the air handler is installed, or 3 CFM per 100 square feet if it is not. For new construction, a passing duct leakage test is mandatory before a home can be granted an occupancy certificate.

If your home in Barnegat township, NJ cannot achieve a passing duct leakage score, you are likely wasting money on heating and cooling — and increasing wear on your HVAC system over time. Meeting the 3–4 CFM requirement matters not only for code compliance, but also for protecting your home’s comfort and reducing energy waste.

Your technician will also offer professional recommendations to tackle leakage issues so you can secure a passing score, reduce utility costs, and strengthen home performance.

Local Energy Audits — affordable duct leakage test in Barnegat township, NJ

Local Energy Audits is proud to serve families and builders across Barnegat township, NJ and the surrounding local areas. We specialize in detecting duct leakage and reducing energy inefficiencies using blower door and duct leakage test. Whether you’re creating a new home or improving an existing one, we’re here to assist.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.