Duct Leakage Test in Bear, DE

How a Duct Leakage Test Is Conducted

To start the duct testing process in Bear, DE, the technician seals all supply and return registers except for the main return or the air handler. A calibrated duct blaster fan is then mounted to the opening. This fan creates negative pressure inside the ducts, making air leakage locations easier to find.

The duct blaster, working hand in hand with a precision pressure sensor, measures airflow and identifies leaks in the ductwork without impacting your home. A duct leakage test — frequently called a duct blaster test — reveals air escape points in your ducts, guiding you toward the best sealing options.

duct leakage test is rapid, clean, and performed without inconvenience to residents. Most tests in Bear, DE are done in about 30 to 60 minutes, and the resulting enhancements can support your home’s comfort and efficiency for many years.

How to Measure Duct Leakage

Duct leakage is monitored in cubic feet per minute (CFM) per 100 square feet of the conditioned sections of the home. Your technician uses a nanometer to read small pressure variations, helping determine the volume of air escaping through the ducts. Understanding this number helps you detect inefficiencies, assess needed upgrades, and ensure your home complies with local energy code requirements in Bear, DE.

Cost of Excessive Duct Leakage

If you observe rising utility costs, temperature swings in different rooms, or regular HVAC breakdowns, duct leakage may be involved. According to ENERGY STAR, typical duct systems lose 20% to 30% of conditioned air through leaks. Hot or cold outdoor air infiltrating your system makes your HVAC system work overtime, which boosts energy costs and reduces comfort.

Overworked equipment also causes additional breakdowns and increases repair costs. Proper duct sealing helps sustain your HVAC system’s long-term condition, increasing its operational lifespan and decreasing maintenance requirements.

Duct leaks can also enable dust, mold spores, elevated moisture, and unwanted contaminants to infiltrate the duct system. This can amplify allergy problems, impact air quality indoors, and slowly create costly structural damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC mandates that new homes include fully sealed duct systems built with energy-efficient materials like mastic, foil tape, and proper insulation. But what about leaks that lie far within enclosed wall or ceiling spaces?

Aerosol sealing technology (AeroSeal) makes it possible to seal leaks found deep within the ductwork. To implement this method, every vent is covered except one access point. The HVAC system is isolated, and a machine is connected to the duct system. It pressurizes the ducts and sprays a fine mist of sealant that fills tiny leaks and holes beyond the reach of conventional sealing.

This method is effective at treating small to medium leaks. However, big openings may still need to be addressed with manual mastic-and-tape sealing. Technicians conduct a duct leakage test before and after aerosol sealing to measure how much the leakage has been reduced and ensure the treatment is successful.

Common Areas of Duct Leakage

The most common leakage area in duct systems is the joints. Ductwork involves numerous metal parts pressed together with tight fittings and metal bands, but these connections are almost never fully airtight.

As your HVAC system heats and cools during seasonal changes, the ductwork expands and then contracts. Over time, this movement makes joints shift and loosen, forming gaps and leaks — which is why a duct leakage test is advised for homes old and new in Bear, DE.

Many energy auditors detect duct leakage by physically checking the ducts and using a small tool to assess the width of joint gaps. If your duct system isn’t sealed with mastic and approved tape, there’s a good chance that leaks are occurring.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system should come out under 4 CFM per 100 square feet in tests with the air handler, or 3 CFM per 100 square feet without the air handler. For new construction, you must pass a duct leakage test before the home can be approved for an occupancy certificate.

If your home in Bear, DE cannot achieve a passing duct leakage score, you are likely wasting money on heating and cooling — and increasing wear on your HVAC system over time. Meeting the 3–4 CFM requirement is essential not only for code compliance but also for protecting your home’s energy efficiency and comfort.

Your technician will also provide expert recommendations on how to address leakage issues so you can achieve a passing score, lower your utility bills, and improve your home’s overall performance.

Local Energy Audits — affordable duct leakage test in Bear, DE

Local Energy Audits proudly helps clients across Bear, DE and surrounding communities. We specialize in locating and diagnosing duct leakage and energy inefficiencies through blower door and duct leakage tests. Whether your home is newly built or older, we’re here to help.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.