Duct Leakage Test in Glen Rock, NJ

How a Duct Leakage Test Is Conducted

To perform a duct leakage test in Glen Rock, NJ, the technician begins by sealing every supply and return register except for the primary return or air handler unit. A specially calibrated fan known as a duct blaster is then put in place at the opening. It depressurizes the ductwork so escaping air can be accurately identified.

The duct blaster uses its precision pressure sensor partner to measure airflow and uncover duct leaks without causing any home disruption. A duct leakage test — widely known as a duct blaster test — pinpoints air leakage in your ducts so you can choose the best sealing methods.

duct leakage test is quick, low-impact, and does not disturb residents. Most tests in Glen Rock, NJ take around 30 to 60 minutes, but the efficiency and comfort improvements can last for many years.

How to Measure Duct Leakage

Duct leakage is quantified in cubic feet per minute (CFM) for each 100 square feet of conditioned living space. Your technician uses a nanometer to identify subtle pressure differences, helping determine how much air is leaking from the ducts. Understanding this number enables you to recognize problem areas, consider efficiency improvements, and verify that your home meets local energy code requirements in Glen Rock, NJ.

Cost of Excessive Duct Leakage

If you’re encountering increased energy bills, temperature inconsistencies, or constant HVAC repairs, duct leakage could be the source. According to ENERGY STAR, the average household loses 20%–30% of conditioned air because of leaking ducts. If outdoor hot or cold air infiltrates your system, your HVAC struggles to maintain temperatures, raising energy costs and lowering comfort.

Overworked equipment also causes components to fail more often, leading to costly repairs. Proper duct sealing helps maintain the long-term health of your HVAC system, extending its lifespan and reducing ongoing maintenance needs.

Duct leaks can also create openings for dust, mold spores, moisture, and various contaminants to enter the duct system. This can worsen allergy conditions, affect indoor air quality, and result in costly damage forming behind walls or ceilings over time.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC calls for new homes to include duct systems that are completely sealed using efficient materials such as mastic, foil tape, and insulation. But what happens when air leaks are concealed deep in the walls or ceilings?

Aerosol sealing technology (AeroSeal) can identify and seal leaks that lie deep inside ductwork. To set up this method, all vents are sealed off except for a single access point. The HVAC system is isolated, and a machine is fitted to the duct system. It pressurizes the ducts and releases a fine sealant mist that finds and fills small holes that traditional sealing methods cannot access.

This method excels at sealing small to medium leaks. However, bigger holes often must be sealed manually with mastic and tape. Technicians complete a duct leakage test before and after aerosol sealing to track leakage reduction and confirm the treatment’s success.

Common Areas of Duct Leakage

The most typical place where ducts leak air is at their joints. Ductwork is built from multiple metal sections pressed tightly with fittings and metal bands, yet these joints are rarely airtight.

As your HVAC system moves through annual heating and cooling cycles, the ductwork expands and then contracts. Over time, this movement makes the joints loosen, forming gaps and leaks — meaning a duct leakage test is advised for both new and older homes in Glen Rock, NJ.

Many energy auditors examine duct leakage by touching the ducts and using a small tool to measure the gap width between joints. If your duct system has not been properly sealed with mastic and approved tape, it’s very likely that leakage exists.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must read under 4 CFM per 100 square feet with the air handler installed, or 3 CFM per 100 square feet without the air handler. For new construction, a passing duct leakage test is a required step before final occupancy certification can be awarded.

If your home in Glen Rock, NJ falls short in a duct leakage test, you are probably paying extra for heating and cooling — and placing lasting pressure on your HVAC equipment. Meeting the 3–4 CFM requirement is vital not only for satisfying code rules but also for preserving your home’s comfort and energy performance.

Your technician will also provide expert strategies to address leakage concerns, helping you achieve a passing score, bring down utility bills, and boost home efficiency.

Local Energy Audits — affordable duct leakage test in Glen Rock, NJ

Local Energy Audits is proud to work with customers in Glen Rock, NJ and all nearby areas. We specialize in finding duct leakage and energy inefficiencies through blower door tests and duct leakage tests. Whether you’re constructing a new home or upgrading an older one, we’re ready to assist.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.