Duct Leakage Test in Hackensack, NJ

How a Duct Leakage Test Is Conducted

To set up a duct leakage test in Hackensack, NJ, the technician begins by sealing all supply and return registers, leaving only the air handler or main return open. A duct blaster — a specially calibrated fan — is then connected to the opening. It depressurizes the duct system to expose areas where air is leaking.

The duct blaster, combined with a precision pressure sensor, measures airflow and detects leaks in the duct system without causing any disturbance in your home. A duct leakage test — also called a duct blaster test — locates the points where duct air escapes, helping you implement the right sealing solution.

duct leakage test is prompt, clean, and does not interrupt residents’ activities. Most tests in Hackensack, NJ take between 30 and 60 minutes, and the improvements they deliver can elevate comfort and efficiency for years ahead.

How to Measure Duct Leakage

Duct leakage is evaluated in cubic feet per minute (CFM) per 100 square feet of conditioned space inside the home. Your technician uses a nanometer to measure tiny pressure changes, revealing how much air is escaping through the ducts. Understanding this number gives you insight into problem areas, helps you plan improvements, and ensures your home meets local energy code requirements in Hackensack, NJ.

Cost of Excessive Duct Leakage

If you observe rising utility costs, temperature swings in different rooms, or regular HVAC breakdowns, duct leakage may be involved. According to ENERGY STAR, many homes lose as much as 20% to 30% of conditioned air through duct leaks. Air entering from outside—whether warm or cold—makes your HVAC operate harder, causing energy costs to climb and comfort to decrease.

Overworked equipment also heightens the chance of system failures and expensive repairs. Proper duct sealing helps sustain your HVAC system’s long-term condition, increasing its operational lifespan and decreasing maintenance requirements.

Duct leaks can also enable dust, mold spores, elevated moisture, and unwanted contaminants to infiltrate the duct system. This can heighten allergy issues, compromise indoor air quality, and slowly cause expensive structural damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC requires new homes to have fully sealed duct systems using modern, energy-efficient materials such as mastic, foil tape, and insulation. But what do you do about leaks that sit deep within walls or ceilings?

Aerosol sealing technology (AeroSeal) is used to address openings concealed inside duct systems. To implement this method, every vent is covered except one access point. The HVAC system is isolated, and a machine is connected to the duct system. It pressurizes the ducts and emits a fine aerosol sealant that fills tiny gaps and holes that standard sealing methods can’t access.

This method provides strong results for small and medium leaks. However, significant openings may still require mastic and tape by hand. Technicians use a duct leakage test before and after aerosol sealing to evaluate how much leakage has been lowered and verify the results.

Common Areas of Duct Leakage

The most common place for ducts to leak air is through the joints. Ductwork is made of multiple metal pieces pressed together using tight fittings and metal bands, but these connections are rarely airtight.

As your HVAC system transitions between warm and cool air throughout the year, the ducts expand and contract. Over time, this movement loosens the joints, causing gaps and leaks — which is why both new and older homes in Hackensack, NJ should consider a duct leakage test.

Many energy auditors investigate duct leakage by running their hands over the ducts and using a small tool to determine the width of joint gaps. If your duct system wasn’t properly sealed using mastic and approved tape, air leakage is very likely occurring.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system needs to be under 4 CFM per 100 square feet when the air handler is installed, or 3 CFM per 100 square feet when it isn’t. For new construction, passing a duct leakage test is required before a home can receive an occupancy certificate.

If your home in Hackensack, NJ fails its duct leakage test, you are likely facing inflated heating and cooling costs — along with increased strain on your HVAC system. Meeting the 3–4 CFM requirement is key not only for staying code-compliant but for maintaining energy efficiency and consistent comfort in your home.

Your technician will also share expert recommendations for fixing leakage problems, helping you achieve a passing score, save on utilities, and improve home performance.

Local Energy Audits — affordable duct leakage test in Hackensack, NJ

Local Energy Audits proudly covers Hackensack, NJ and all nearby towns. We specialize in measuring duct leakage and energy inefficiencies using advanced blower door and duct leakage tests. Whether you’re building new or improving old, we’re here to help.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.