Duct Leakage Test in Oakland, NJ

How a Duct Leakage Test Is Conducted

To initiate a duct leakage test in Oakland, NJ, your technician seals all supply and return registers, leaving only the main return or air handler open. A calibrated duct blaster fan is then mounted to the opening. This fan creates negative pressure inside the ducts, making air leakage locations easier to find.

The duct blaster system, along with a precision pressure sensor, measures airflow and highlights leaks in the ductwork without inconveniencing you at home. A duct leakage test — often referred to as a duct blaster test — identifies air loss in your ducts, allowing you to find the most effective ways to seal them.

duct leakage test is prompt, clean, and does not interrupt residents’ activities. Most tests in Oakland, NJ take between 30 and 60 minutes, and the improvements they deliver can elevate comfort and efficiency for years ahead.

How to Measure Duct Leakage

Duct leakage is recorded in cubic feet per minute (CFM) per 100 square feet of the conditioned portion of the home. Your technician uses a nanometer to identify subtle pressure differences, helping determine how much air is leaking from the ducts. Understanding this number gives you insight into problem areas, helps you plan improvements, and ensures your home meets local energy code requirements in Oakland, NJ.

Cost of Excessive Duct Leakage

If your energy bills are unusually high, your rooms feel unevenly heated or cooled, or your HVAC system needs frequent repairs, duct leakage could be the issue. According to ENERGY STAR, homes across the country lose 20% to 30% of their conditioned air through duct leakage. Air entering from outside—whether warm or cold—makes your HVAC operate harder, causing energy costs to climb and comfort to decrease.

Overworked equipment also leads to more breakdowns and costly repairs. Proper duct sealing helps promote the long-term integrity of your HVAC system, extending its lifespan and limiting continued maintenance needs.

Duct leaks can also draw in dust, mold spores, unwanted moisture, and other harmful contaminants. This can irritate allergies, harm the air quality inside, and cause expensive hidden structural damage as time goes on.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC mandates that new homes include fully sealed duct systems built with energy-efficient materials like mastic, foil tape, and proper insulation. But what if some leaks are hidden within the depths of your walls or ceilings?

Aerosol sealing technology (AeroSeal) helps seal hard-to-find openings within the duct system. To implement this method, every vent is covered except one access point. The HVAC system is isolated, and a machine is connected to the duct system. It pressurizes the ducts and pushes a fine aerosol sealant through them, sealing small holes that ordinary sealing methods can’t reach.

This method works very well for small to medium leaks. However, larger openings may still need to be sealed manually with mastic and tape. Technicians carry out a duct leakage test before and after aerosol sealing to assess how much leakage has improved and ensure the treatment was effective.

Common Areas of Duct Leakage

The most usual spot for duct air leakage is the joints. Ductwork is composed of various metal pieces pressed together using tight fittings and metal bands, but these seals are hardly ever fully airtight.

As your HVAC system runs through seasonal heating and cooling, the ducts experience ongoing expansion and contraction. Over time, this movement causes joints to lose their seal, creating gaps and leaks — making a duct leakage test valuable for any home in Oakland, NJ, whether new or old.

Many energy auditors investigate duct leakage by running their hands over the ducts and using a small tool to determine the width of joint gaps. If your duct system has not been properly sealed with mastic and approved tape, it’s very likely that leakage exists.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system has to be under 4 CFM per 100 square feet when the air handler is in place, or 3 CFM per 100 square feet without it installed. For new construction, a passing duct leakage test is essential before the home can qualify for an occupancy certificate.

If your home in Oakland, NJ doesn’t achieve a passing duct leakage score, you’re likely overspending on heating and cooling — and putting extended strain on your HVAC unit. Meeting the 3–4 CFM requirement is fundamental not only for code adherence but for boosting your home’s long-term efficiency and comfort.

Your technician will also provide professional insights on resolving leakage issues so you can achieve a passing score, lower your utility costs, and optimize home performance.

Local Energy Audits — affordable duct leakage test in Oakland, NJ

Local Energy Audits proudly supports customers throughout Oakland, NJ and the areas nearby. We specialize in locating and diagnosing duct leakage and energy inefficiencies through blower door and duct leakage tests. Whether your home is newly built or older, we’re here to help.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.