Duct Leakage Test in Oradell borough, NJ

How a Duct Leakage Test Is Conducted

To kick off a duct leakage test in Oradell borough, NJ, your technician will block all supply and return registers while keeping the main return or air handler accessible. A specially calibrated device known as a duct blaster is then attached to the duct opening. Its purpose is to depressurize the system so that escaping air can be detected.

The duct blaster uses a precision pressure sensor to monitor airflow and pinpoint leaks throughout the ductwork without interrupting your home environment. A duct leakage test — often referred to as a duct blaster test — identifies air loss in your ducts, allowing you to find the most effective ways to seal them.

duct leakage test is simple, clean, and minimally invasive for residents. Most tests in Oradell borough, NJ take just 30 to 60 minutes, and the resulting improvements can enhance your home’s comfort and efficiency long-term.

How to Measure Duct Leakage

Duct leakage is measured using cubic feet per minute (CFM) per 100 square feet of conditioned floor area. Your technician uses a nanometer to detect pressure variations, helping quantify the amount of duct leakage. Understanding this number helps you recognize where issues exist, plan meaningful improvements, and check your home against local energy code requirements in Oradell borough, NJ.

Cost of Excessive Duct Leakage

If you’re facing higher energy bills, uneven heating or cooling, or recurring HVAC repairs, duct leakage could be to blame. According to ENERGY STAR, an average home’s ductwork loses 20% to 30% of conditioned air through leaks. When outside hot or cold air seeps into your system, your HVAC must compensate, leading to higher energy costs and diminished comfort.

Overworked equipment also produces more frequent issues that require costly repairs. Proper duct sealing helps enhance the long-term resilience of your HVAC system, lengthening its lifespan and cutting overall maintenance needs.

Duct leaks can also allow dust, mold spores, excess moisture, and other contaminants into the duct system. This can worsen allergy flare-ups, reduce indoor air quality, and cause long-term structural deterioration behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC calls for new homes to include duct systems that are completely sealed using efficient materials such as mastic, foil tape, and insulation. But what happens when leaks are hidden deep inside walls or ceilings?

Aerosol sealing technology (AeroSeal) can identify and seal leaks that lie deep inside ductwork. To carry out this method, every vent is sealed except a single access point. The HVAC system is separated, and a machine is attached to the duct system. It pressurizes the ducts and injects a fine aerosolized sealant that targets small holes and gaps unreachable by traditional sealing methods.

This method is very effective for minor to moderate leaks. However, substantial openings may still need traditional sealing with mastic and tape. Technicians carry out a duct leakage test before and after aerosol sealing to assess how much leakage has improved and ensure the treatment was effective.

Common Areas of Duct Leakage

The most common spot where air escapes in duct systems is the joints. Ductwork features several metal pieces pressed together using tight fittings and metal bands, though these areas are seldom airtight.

As your HVAC system operates in both heating and cooling modes year-round, the ducts continuously expand and contract. Over time, this movement leads the joints to loosen, resulting in gaps and leaks — making a duct leakage test important for new and older homes in Oradell borough, NJ.

Many energy auditors check duct leakage by feeling around the ducts and using a small tool to test the width of gaps between joints. If your duct system was not sealed with mastic and approved tape, there’s a high likelihood that air is leaking.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must remain below 4 CFM per 100 square feet with the air handler installed, or 3 CFM per 100 square feet if the air handler is missing. For new construction, you must pass a duct leakage test before the home can be approved for an occupancy certificate.

If your home in Oradell borough, NJ does not meet duct leakage standards, you are likely overpaying for heating and cooling — and adding unnecessary strain to your HVAC equipment. Meeting the 3–4 CFM requirement is indispensable not only for compliance purposes but for ensuring strong comfort and energy savings.

Your technician will also give professional advice on resolving leakage issues to help you achieve a passing score, cut down utility bills, and boost your home’s performance.

Local Energy Audits — affordable duct leakage test in Oradell borough, NJ

Local Energy Audits is proud to serve families and builders across Oradell borough, NJ and the surrounding local areas. We specialize in diagnosing duct leakage and energy inefficiencies through blower door and duct leakage test. Whether your home is new or existing, we’re ready to help.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.