Duct Leakage Test in Pennsauken township, NJ

How a Duct Leakage Test Is Conducted

To set up a duct leakage test in Pennsauken township, NJ, the technician begins by sealing all supply and return registers, leaving only the air handler or main return open. A duct blaster — a specially calibrated fan — is then connected to the opening. It depressurizes the duct system to expose areas where air is leaking.

The duct blaster works in sync with a precision pressure sensor to assess airflow and find duct leaks without disturbing your living space. A duct leakage test — widely known as a duct blaster test — pinpoints air leakage in your ducts so you can choose the best sealing methods.

duct leakage test is quick, low-impact, and does not disturb residents. Most tests in Pennsauken township, NJ are performed within 30 to 60 minutes, and the positive impact on comfort and efficiency can remain for years.

How to Measure Duct Leakage

Duct leakage is calculated in cubic feet per minute (CFM) for every 100 square feet of conditioned space. Your technician uses a nanometer to register small pressure differences, which help calculate how much air is leaking from the ducts. Understanding this number gives you insight into problem areas, helps you plan improvements, and ensures your home meets local energy code requirements in Pennsauken township, NJ.

Cost of Excessive Duct Leakage

If you’re struggling with expensive utility bills, inconsistent indoor temperatures, or continual HVAC problems, duct leakage might be the culprit. According to ENERGY STAR, many homes lose as much as 20% to 30% of conditioned air through duct leaks. Outside air that’s too hot or too cold entering your system strains your HVAC, resulting in higher energy consumption and less comfort.

Overworked equipment also causes components to fail more often, leading to costly repairs. Proper duct sealing helps support your HVAC system’s long-term operation, increasing its lifespan and lowering frequent maintenance needs.

Duct leaks can also draw in dust, mold spores, unwanted moisture, and other harmful contaminants. This can worsen allergies, reduce indoor air quality, and even cause expensive structural damage behind walls or ceilings over time.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC instructs that new homes incorporate fully sealed duct systems using high-efficiency materials, including mastic, foil tape, and insulation. But what about leaks that occur deep behind walls or ceilings out of sight?

Aerosol sealing technology (AeroSeal) is used to address openings concealed inside duct systems. To perform the technique, all vents are sealed except a single access opening. The HVAC system is isolated, and a machine is hooked into the duct system. It pressurizes the ducts and injects a fine aerosolized sealant that targets small holes and gaps unreachable by traditional sealing methods.

This method is highly effective for small to medium leaks. However, large openings may still require manual sealing with mastic and tape. Technicians conduct a duct leakage test before and after aerosol sealing to measure how much the leakage has been reduced and ensure the treatment is successful.

Common Areas of Duct Leakage

The most frequent point of air leakage in ductwork is the joints. Multiple metal parts are pressed together using tight fittings and metal bands, although these junctions are seldom airtight.

As your HVAC system delivers heat and cooling across different seasons, the ducts constantly expand and contract. Over time, this movement results in loose joints that create gaps and leaks — making a duct leakage test necessary for new and older homes in Pennsauken township, NJ.

Many energy auditors detect leaks by checking the duct surfaces by hand and using a small tool to measure joint gap width. If your duct system hasn’t been finished with mastic and approved tape, leaks are highly likely.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must come in under 4 CFM per 100 square feet with the air handler, or 3 CFM per 100 square feet when the air handler is removed. For new construction, homes are required to pass a duct leakage test before an occupancy certificate can be issued.

If your home in Pennsauken township, NJ does not pass its duct leakage inspection, you’re likely paying higher heating and cooling bills — and stressing your HVAC system over time. Meeting the 3–4 CFM requirement is essential not only for following building code, but for keeping your home comfortable and energy-efficient.

Your technician will also give informed guidance on addressing leakage problems, enabling you to pass the test, reduce energy bills, and enhance your home’s performance.

Local Energy Audits — affordable duct leakage test in Pennsauken township, NJ

Local Energy Audits proudly offers services throughout Pennsauken township, NJ and neighboring areas. We specialize in diagnosing duct leakage and energy inefficiencies through blower door and duct leakage test. Whether your home is new or existing, we’re ready to help.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.