Duct Leakage Test in Runnemede borough, NJ

How a Duct Leakage Test Is Conducted

To begin the process of a duct leakage test in Runnemede borough, NJ, your technician seals off all supply and return registers apart from the main return or air handler. A duct blaster, which is a specially calibrated fan, is then installed at the opening. The fan depressurizes the ducts, helping identify all points where air may be escaping.

The duct blaster teams up with a precision pressure sensor to measure airflow accurately and locate duct leaks without affecting your home. A duct leakage test — sometimes referred to as a duct blaster test — uncovers air leaks in your ductwork so you can determine the ideal sealing approach.

duct leakage test is efficient, mess-free, and completely non-intrusive for residents. Most tests in Runnemede borough, NJ take around 30 to 60 minutes, but the efficiency and comfort improvements can last for many years.

How to Measure Duct Leakage

Duct leakage is monitored in cubic feet per minute (CFM) per 100 square feet of the conditioned sections of the home. Your technician uses a nanometer to monitor tiny pressure fluctuations that indicate how much air is leaking through the ducts. Understanding this number allows you to pinpoint problem areas, assess needed improvements, and confirm whether your home satisfies local energy code requirements in Runnemede borough, NJ.

Cost of Excessive Duct Leakage

If you’re facing higher energy bills, uneven heating or cooling, or recurring HVAC repairs, duct leakage could be to blame. According to ENERGY STAR, the average duct system loses between 20% and 30% of its conditioned air due to leaks. Hot or cold outdoor air infiltrating your system makes your HVAC system work overtime, which boosts energy costs and reduces comfort.

Overworked equipment also leads to more breakdowns and costly repairs. Proper duct sealing helps preserve the long-term efficiency of your HVAC system, boosting its lifespan and cutting down on regular maintenance needs.

Duct leaks can also pull dust, mold spores, excess moisture, and various contaminants into the duct system. This can increase allergy discomfort, degrade indoor air quality, and eventually cause expensive structural issues behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC requires all newly constructed homes to have fully sealed ductwork with modern, energy-saving materials such as mastic, foil tape, and insulation. But what about leaks that occur deep behind walls or ceilings out of sight?

Aerosol sealing technology (AeroSeal) provides a way to seal concealed openings inside the duct system. To carry out this method, every vent is sealed except a single access point. The HVAC system is separated, and a machine is attached to the duct system. It pressurizes the ducts and sends out a fine aerosol mist that seals tiny openings traditional sealing cannot reach.

This method is ideal for small to medium leaks. However, any large openings will still need manual sealing with mastic and tape. Technicians carry out leakage testing prior to and after aerosol sealing to observe the reduction and ensure treatment success.

Common Areas of Duct Leakage

The most typical place for ducts to lose air is at the joints. Ductwork consists of different metal sections pressed together with tight fittings and metal bands, yet these joints are not usually airtight.

As your HVAC system changes between heating and cooling during the year, the ducts naturally expand and shrink. Over time, this movement compromises the joints, forming gaps and leaks — which is exactly why duct leakage test is encouraged for new and older homes in Runnemede borough, NJ.

Many energy auditors look for duct leakage by running their hands along the ducts and using a small tool to measure the width of gaps at the joints. If your duct system does not include sealing with mastic and approved tape, leakage is highly likely.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system should measure under 4 CFM per 100 square feet with the air handler installed, or 3 CFM per 100 square feet without the air handler installed. For new construction, an occupancy certificate cannot be issued unless the home passes a duct leakage test.

If your home in Runnemede borough, NJ doesn’t achieve a passing duct leakage score, you’re likely overspending on heating and cooling — and putting extended strain on your HVAC unit. Meeting the 3–4 CFM requirement is indispensable not only for compliance purposes but for ensuring strong comfort and energy savings.

Your technician will also share expert recommendations for fixing leakage problems, helping you achieve a passing score, save on utilities, and improve home performance.

Local Energy Audits — affordable duct leakage test in Runnemede borough, NJ

Local Energy Audits is proud to serve customers across Runnemede borough, NJ and the nearby communities. We specialize in locating and diagnosing duct leakage and energy inefficiencies through blower door and duct leakage tests. Whether your home is newly built or older, we’re here to help.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.