Duct Leakage Test in Tavistock, NJ

How a Duct Leakage Test Is Conducted

To begin a duct leakage test in Tavistock, NJ, your technician will seal off all supply and return registers except for the main return or the air handler. A specially calibrated device known as a duct blaster is then attached to the duct opening. Its purpose is to depressurize the system so that escaping air can be detected.

The duct blaster, working hand in hand with a precision pressure sensor, measures airflow and identifies leaks in the ductwork without impacting your home. A duct leakage test — often known as a duct blaster test — exposes duct air loss, allowing you to apply the most effective sealing techniques.

duct leakage test is fast, debris-free, and completely resident-friendly. Most tests in Tavistock, NJ take between 30 and 60 minutes, and the improvements they deliver can elevate comfort and efficiency for years ahead.

How to Measure Duct Leakage

Duct leakage is expressed in cubic feet per minute (CFM) per 100 square feet of the home’s conditioned area. Your technician uses a nanometer to monitor tiny pressure fluctuations that indicate how much air is leaking through the ducts. Understanding this number helps you uncover weak points, analyze opportunities for upgrades, and check whether your home follows local energy code requirements in Tavistock, NJ.

Cost of Excessive Duct Leakage

If your energy bills are unusually high, your rooms feel unevenly heated or cooled, or your HVAC system needs frequent repairs, duct leakage could be the issue. According to ENERGY STAR, typical duct systems lose 20% to 30% of conditioned air through leaks. When hot or cold outside air enters your system, your HVAC has to work harder, increasing energy costs and lowering overall comfort.

Overworked equipment also triggers more mechanical failures and costly service calls. Proper duct sealing helps safeguard the long-term reliability of your HVAC system, extending its lifespan and reducing how often maintenance is needed.

Duct leaks can also let in dust, mold spores, added moisture, and other harmful contaminants. This can irritate allergies, harm the air quality inside, and cause expensive hidden structural damage as time goes on.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC specifies that newly constructed homes must use fully sealed duct systems with modern, efficient materials such as mastic, foil tape, and insulation. But what happens when air leaks are concealed deep in the walls or ceilings?

Aerosol sealing technology (AeroSeal) helps seal hard-to-find openings within the duct system. To set up this method, all vents are sealed off except for a single access point. The HVAC system is isolated, and a machine is fitted to the duct system. It pressurizes the ducts and emits a fine aerosol sealant that fills tiny gaps and holes that standard sealing methods can’t access.

This method is highly effective for small to medium leaks. However, large openings may still require manual sealing with mastic and tape. Technicians use before-and-after duct leakage tests to measure improvement and make sure the aerosol sealing process was successful.

Common Areas of Duct Leakage

The most frequent area where ducts lose air is at the joints. Ductwork consists of several metal sections pressed together with tight fittings and metal bands, yet these connections are almost never fully airtight.

As your HVAC system operates in both heating and cooling modes year-round, the ducts continuously expand and contract. Over time, this movement weakens the joints, creating gaps and leaks — a key reason duct leakage test is recommended for new and older homes in Tavistock, NJ.

Many energy auditors evaluate duct leakage by feeling around the duct system and using a small tool to check the size of joint gaps. If your duct system has not been sealed with mastic and approved tape, there is a high chance that leakage is occurring.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system has to be under 4 CFM per 100 square feet when the air handler is in place, or 3 CFM per 100 square feet without it installed. For new construction, an occupancy certificate cannot be issued unless the home passes a duct leakage test.

If your home in Tavistock, NJ falls short in a duct leakage test, you are probably paying extra for heating and cooling — and placing lasting pressure on your HVAC equipment. Meeting the 3–4 CFM requirement is significant not only for meeting local code but also for maintaining optimal comfort and efficiency in your home.

Your technician will also give informed guidance on addressing leakage problems, enabling you to pass the test, reduce energy bills, and enhance your home’s performance.

Local Energy Audits — affordable duct leakage test in Tavistock, NJ

Local Energy Audits is proud to assist customers across Tavistock, NJ and its surrounding communities. We specialize in diagnosing duct leakage and energy inefficiencies through blower door and duct leakage test. Whether your home is new or existing, we’re ready to help.
If you’d like to schedule a test, call us during business hours or contact us online to request an appointment.