Duct Leakage Test in Warminster, PA

How a Duct Leakage Test Is Conducted

To set up a duct leakage test in Warminster, PA, the technician begins by sealing all supply and return registers, leaving only the air handler or main return open. A duct blaster, which is a specially calibrated fan, is then installed at the opening. The fan depressurizes the ducts, helping identify all points where air may be escaping.

The duct blaster and its precision pressure sensor work together to measure airflow and detect duct leaks without causing any disruption in your home. A duct leakage test — sometimes known as a duct blaster test — shows exactly where your ducts are leaking air so you can apply the right sealing fixes.

duct leakage test is quick, neat, and intentionally non-intrusive for anyone living in the home. Most tests in Warminster, PA are done within 30 to 60 minutes, with improvements that strengthen comfort and efficiency for years to come.

How to Measure Duct Leakage

Duct leakage is expressed in cubic feet per minute (CFM) per 100 square feet of the home’s conditioned area. Your technician uses a nanometer to identify pressure differences, which provide a clear picture of how much air is leaking from the ductwork. Understanding this number enables you to recognize problem areas, consider efficiency improvements, and verify that your home meets local energy code requirements in Warminster, PA.

Cost of Excessive Duct Leakage

If you’re experiencing spikes in utility bills, uncomfortable temperature variations, or ongoing HVAC repair needs, duct leakage may be to blame. According to ENERGY STAR, duct leakage causes homeowners to lose 20%–30% of their conditioned air on average. Hot or cold outside air entering your system forces your HVAC system to work harder, driving up energy costs and reducing comfort.

Overworked equipment also contributes to repeated breakdowns and pricey repairs. Proper duct sealing helps uphold the long-term performance of your HVAC system, stretching its lifespan and decreasing routine maintenance demands.

Duct leaks can also allow dust, mold spores, excess moisture, and other contaminants into the duct system. This can heighten allergy issues, compromise indoor air quality, and slowly cause expensive structural damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC outlines that new homes must be built with fully sealed duct systems, utilizing materials like mastic, foil tape, and insulation to enhance energy efficiency. But what if leaks are concealed deep inside the structure of your walls or ceilings?

Aerosol sealing technology (AeroSeal) allows technicians to seal leaks located inside inaccessible parts of ductwork. To begin this method, every vent is sealed except for one access opening. The HVAC unit is isolated, and a machine is installed onto the duct system. It pressurizes the ducts and injects a fine aerosolized sealant that targets small holes and gaps unreachable by traditional sealing methods.

This method works best for small to medium leaks. However, large openings usually require traditional manual sealing using mastic and tape. Technicians complete a duct leakage test before and after aerosol sealing to track leakage reduction and confirm the treatment’s success.

Common Areas of Duct Leakage

The most frequent point of air leakage in ductwork is the joints. Multiple metal parts are pressed together using tight fittings and metal bands, although these junctions are seldom airtight.

As your HVAC system heats and cools throughout the year, the ducts expand and contract. Over time, this movement makes joints shift and loosen, forming gaps and leaks — which is why a duct leakage test is advised for homes old and new in Warminster, PA.

Many energy auditors check duct leakage by feeling around the ducts and using a small tool to test the width of gaps between joints. If your duct system hasn’t been sealed with mastic and approved tape, there is a strong likelihood that leakage is happening.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system should measure under 4 CFM per 100 square feet with the air handler installed, or 3 CFM per 100 square feet without the air handler installed. For new construction, a passing duct leakage test is mandatory before a home can be granted an occupancy certificate.

If your home in Warminster, PA is unable to pass a duct leakage test, you are probably spending too much on heating and cooling — while your HVAC equipment endures long-term stress. Meeting the 3–4 CFM requirement is significant not only for meeting local code but also for maintaining optimal comfort and efficiency in your home.

Your technician will also provide professional insights on resolving leakage issues so you can achieve a passing score, lower your utility costs, and optimize home performance.

Local Energy Audits — affordable duct leakage test in Warminster, PA

Local Energy Audits proudly supports customers throughout Warminster, PA and the areas nearby. We specialize in detecting duct leakage and energy inefficiencies using blower door and duct leakage test. Whether you’re building new or enhancing your current home, we’re here to support you.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.