Duct Leakage Test in Woodbury city, NJ

How a Duct Leakage Test Is Conducted

To set up a duct leakage test in Woodbury city, NJ, the technician begins by sealing all supply and return registers, leaving only the air handler or main return open. A specially calibrated fan known as a duct blaster is then put in place at the opening. It depressurizes the ductwork so escaping air can be accurately identified.

The duct blaster collaborates with a precision pressure sensor to evaluate airflow and locate leaks throughout the ductwork without disturbing your household. A duct leakage test — sometimes called a duct blaster test — reveals where your ducts are losing air so you can determine the most effective sealing solutions.

duct leakage test is straightforward, clean, and designed to be non-intrusive for residents. Most tests in Woodbury city, NJ are wrapped up in 30 to 60 minutes, with improvements that continue to boost comfort and efficiency for years.

How to Measure Duct Leakage

Duct leakage is monitored in cubic feet per minute (CFM) per 100 square feet of the conditioned sections of the home. Your technician uses a nanometer to measure tiny pressure changes, revealing how much air is escaping through the ducts. Understanding this number allows you to highlight problem zones, explore improvement possibilities, and confirm compliance with local energy code requirements in Woodbury city, NJ.

Cost of Excessive Duct Leakage

If you’re seeing higher energy bills, irregular heating or cooling, or frequent HVAC malfunctions, duct leakage may be at fault. According to ENERGY STAR, the majority of homes lose 20% to 30% of conditioned air through duct leaks. Hot or cold air entering from outside increases the workload on your HVAC system, leading to higher energy bills and a drop in comfort.

Overworked equipment also brings more system failures and higher repair expenses. Proper duct sealing helps protect and extend the long-term lifespan of your HVAC system, minimizing the need for repeated maintenance.

Duct leaks can also pull in dust, mold spores, moisture, and numerous contaminants into the duct system. This can heighten allergy issues, compromise indoor air quality, and slowly cause expensive structural damage behind walls or ceilings.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC calls for new homes to include duct systems that are completely sealed using efficient materials such as mastic, foil tape, and insulation. But what should you do when leaks are located deep within your walls or ceilings?

Aerosol sealing technology (AeroSeal) is used to address openings concealed inside duct systems. To perform the process, technicians seal all vents but leave one access point open. The HVAC system is isolated, and a machine is connected to the duct system. It pressurizes the ducts and releases a fine aerosolized sealant that fills small gaps and holes that traditional sealing methods cannot reach.

This method is extremely effective for sealing small to medium leaks. However, big gaps may still need manual sealing using mastic and tape. Technicians test the ducts for leakage before and after aerosol sealing to determine the reduction level and verify success.

Common Areas of Duct Leakage

The most frequent source of duct air leakage is the joints. Ductwork uses many metal pieces pressed together with tight fittings and metal bands, but these joining points are rarely airtight.

As your HVAC system regulates temperatures through the seasons, the ducts expand when heated and contract when cooled. Over time, this movement gradually loosens the joints, creating leaks and gaps — highlighting the importance of duct leakage test in both new and older homes in Woodbury city, NJ.

Many energy auditors look for duct leakage by running their hands along the ducts and using a small tool to measure the width of gaps at the joints. If your duct system is missing mastic and approved tape sealing, there’s a significant chance that air leakage is happening.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must show under 4 CFM per 100 square feet if the air handler is installed, or 3 CFM per 100 square feet if it is not. For new construction, a duct leakage test must be passed before any home is eligible to receive an occupancy certificate.

If your home in Woodbury city, NJ cannot pass a duct leakage test, you are likely wasting money on heating and cooling — and causing long-term wear on your HVAC system. Meeting the 3–4 CFM requirement is important not only for the inspector, but also for maximizing energy efficiency and comfort in your home.

Your technician will also provide skilled recommendations to resolve leakage problems so you can reach a passing score, decrease energy costs, and improve home performance.

Local Energy Audits — affordable duct leakage test in Woodbury city, NJ

Local Energy Audits proudly helps clients across Woodbury city, NJ and surrounding communities. We specialize in revealing duct leakage and energy inefficiencies through blower door and duct leakage test. Whether your project is new or existing, we’re here to assist.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.