Duct Leakage Test in Longport, NJ

How a Duct Leakage Test Is Conducted

To commence a duct leakage test in Longport, NJ, your technician will seal every supply and return register except the primary return or air handler. A specially calibrated fan, known as a duct blaster, is then attached to the opening. The purpose of this fan is to depressurize the duct system, creating the ideal conditions to identify where air is escaping.

The duct blaster collaborates with a precision pressure sensor to evaluate airflow and locate leaks throughout the ductwork without disturbing your household. A duct leakage test — also called a duct blaster test — locates the points where duct air escapes, helping you implement the right sealing solution.

duct leakage test is swift, clean, and carried out with no disturbance to residents. Most tests in Longport, NJ are done in about 30 to 60 minutes, and the resulting enhancements can support your home’s comfort and efficiency for many years.

How to Measure Duct Leakage

Duct leakage is rated in cubic feet per minute (CFM) per 100 square feet of the home’s conditioned zone. Your technician uses a nanometer to identify pressure differences, which provide a clear picture of how much air is leaking from the ductwork. Understanding this number enables you to recognize problem areas, consider efficiency improvements, and verify that your home meets local energy code requirements in Longport, NJ.

Cost of Excessive Duct Leakage

If you’re struggling with expensive utility bills, inconsistent indoor temperatures, or continual HVAC problems, duct leakage might be the culprit. According to ENERGY STAR, most homes lose 20% to 30% of their conditioned air through leaking ductwork. Hot or cold outdoor air infiltrating your system makes your HVAC system work overtime, which boosts energy costs and reduces comfort.

Overworked equipment also results in more frequent breakdowns and expensive repair bills. Proper duct sealing helps maintain the long-term health of your HVAC system, extending its lifespan and reducing ongoing maintenance needs.

Duct leaks can also introduce dust, mold spores, excess humidity, and other contaminants into the duct system. This can worsen allergies, reduce indoor air quality, and even cause expensive structural damage behind walls or ceilings over time.

How to Properly Seal Ductwork in an Old Home

The 2015 IRC/IECC requires new homes to have fully sealed duct systems using modern, energy-efficient materials such as mastic, foil tape, and insulation. But what about leaks located deep within walls or ceilings?

Aerosol sealing technology (AeroSeal) offers a method to access hidden leaks deep within ductwork. To begin this method, every vent is sealed except for one access opening. The HVAC unit is isolated, and a machine is installed onto the duct system. It pressurizes the ducts and injects a fine aerosolized sealant that targets small holes and gaps unreachable by traditional sealing methods.

This method works efficiently for small to medium leaks. However, larger gaps usually require manual sealing using mastic and tape. Technicians administer a duct leakage test prior to and following aerosol sealing to measure leakage changes and ensure the method was successful.

Common Areas of Duct Leakage

The most common spot where air escapes in duct systems is the joints. Ductwork features several metal pieces pressed together using tight fittings and metal bands, though these areas are seldom airtight.

As your HVAC system shifts between hot and cold cycles all year long, the ductwork expands and contracts. Over time, this movement causes the joints to loosen, creating gaps and leaks — which is why a duct leakage test is recommended for both new and older homes in Longport, NJ.

Many energy auditors examine duct leakage by touching the ducts and using a small tool to measure the gap width between joints. If your duct system wasn’t properly sealed using mastic and approved tape, air leakage is very likely occurring.

What Is an Acceptable Amount of Duct Leakage per Energy Code?

To achieve a passing duct leakage result, your system must read under 4 CFM per 100 square feet with the air handler installed, or 3 CFM per 100 square feet without the air handler. For new construction, the home must pass a duct leakage test before qualifying for an occupancy certificate.

If your home in Longport, NJ fails a duct leakage test, you are probably spending more than you should on heating and cooling — while also putting long-term stress on your HVAC system. Meeting the 3–4 CFM requirement is important not only for the inspector, but also for maximizing energy efficiency and comfort in your home.

Your technician will also give informed guidance on addressing leakage problems, enabling you to pass the test, reduce energy bills, and enhance your home’s performance.

Local Energy Audits — affordable duct leakage test in Longport, NJ

Local Energy Audits is proud to assist customers across Longport, NJ and its surrounding communities. We specialize in identifying duct leakage and energy inefficiencies using blower door tests and duct leakage tests. Whether you’re building a new home or improving an existing one, we’re here to help.
If you’d like to book a test, call us during business hours or contact us online to request an appointment.